ravedude is a CLI utility to make Rust development for AVR microcontrollers
super smooth. It's a wrapper around avrdude and provides easy access to the
target's serial console, similar to the Arduino IDE.
ravedude is meant to be used as a cargo "runner". This allows you to just use
cargo run for building, deploying, and running your AVR code!
if you get an Error: no matching serial port found, use -P or set RAVEDUDE_PORT in your environment ,
run cargo run with set environment variable or adjust runner = "ravedude {X} -cb {X} -P /dev/ttyUSB{X}" inside .cargo/config.toml (replace {X} with your respective values)
On Linux systems, you'll need pkg-config and libudev development files installed:
- Archlinux:
pacman -S systemd pkgconf - Ubuntu/Debian:
apt install libudev-dev pkg-config - Fedora:
dnf install systemd-devel pkgconf-pkg-config
Next, install the latest version from crates.io with the following command:
cargo install ravedudeAlternatively, if you're using Nix (the package manager) + Flakes, you can install ravedude by adding inputs.ravedude.url = "github:Rahix/avr-hal?dir=ravedude"; and use the package ravedude.packages."${system}".default.
Now you need to add ravedude to your project. For example in a project for
Arduino Uno, place the following into your .cargo/config.toml (not in
Cargo.toml):
[target.'cfg(target_arch = "avr")']
runner = "ravedude uno --open-console --baudrate 57600"And that's all, now just call cargo run and watch it do its magic:
avr-hal/examples/arduino-uno on ravedude via v1.51.0-nightly
❯ cargo run --bin uno-i2cdetect
Compiling arduino-uno-examples v0.0.0 (avr-hal/examples/arduino-uno)
Finished dev [optimized + debuginfo] target(s) in 1.26s
Running `ravedude uno -cb 57600 avr-hal/target/avr-atmega328p/debug/uno-i2cdetect.elf`
Board Arduino Uno
Programming avr-hal/target/avr-atmega328p/debug/uno-i2cdetect.elf => /dev/ttyACM0
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.00s
avrdude: Device signature = 0x1e950f (probably m328p)
avrdude: erasing chip
avrdude: reading input file "avr-hal/target/avr-atmega328p/debug/uno-i2cdetect.elf"
avrdude: writing flash (1654 bytes):
Writing | ################################################## | 100% 0.27s
avrdude: 1654 bytes of flash written
avrdude: verifying flash memory against avr-hal/target/avr-atmega328p/debug/uno-i2cdetect.elf:
avrdude: load data flash data from input file avr-hal/target/avr-atmega328p/debug/uno-i2cdetect.elf:
avrdude: input file avr-hal/target/avr-atmega328p/debug/uno-i2cdetect.elf contains 1654 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 0.21s
avrdude: verifying ...
avrdude: 1654 bytes of flash verified
avrdude: safemode: Fuses OK (E:00, H:00, L:00)
avrdude done. Thank you.
Programmed avr-hal/target/avr-atmega328p/debug/uno-i2cdetect.elf
Console /dev/ttyACM0 at 57600 baud
Write direction test:
- 0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- 38 39 -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- 48 -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Read direction test:
- 0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- 38 39 -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- 48 -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
ravedude is licensed under either of
- Apache License, Version 2.0 (LICENSE-APACHE or http://www.apache.org/licenses/LICENSE-2.0)
- MIT license (LICENSE-MIT or http://opensource.org/licenses/MIT)
at your option.