-
Notifications
You must be signed in to change notification settings - Fork 61
/
ue.conf.example
108 lines (103 loc) · 4.29 KB
/
ue.conf.example
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
#####################################################################
# srsUE configuration file
#####################################################################
# RF configuration
#
# dl_freq: Downlink centre frequency (Hz).
# ul_freq: Uplink centre frequency (Hz).
# tx_gain: Transmit gain (dB).
# rx_gain: Optional receive gain (dB). Disables AGC if enabled
#####################################################################
[rf]
dl_freq = 2680000000
ul_freq = 2560000000
tx_gain = 70
#####################################################################
# MAC-layer packet capture configuration
#
# Packets are captured to file in the compact format decoded by
# the Wireshark mac-lte-framed dissector. For more information see:
# https://wiki.wireshark.org/MAC-LTE
#
# enable: Enable MAC layer packet captures (true/false)
# filename: File path to use for packet captures
#####################################################################
[pcap]
enable = false
filename = /tmp/ue.pcap
#####################################################################
# Log configuration
#
# Log levels can be set for individual layers. "all_level" sets log
# level for all layers unless otherwise configured.
# Format: e.g. phy_level = info
#
# In the same way, packet hex dumps can be limited for each level.
# "all_hex_limit" sets the hex limit for all layers unless otherwise
# configured.
# Format: e.g. phy_hex_limit = 32
#
# Logging layers: phy, mac, rlc, pdcp, rrc, nas, gw, usim, all
# Logging levels: debug, info, warning, error, none
#
# filename: File path to use for log output
#####################################################################
[log]
phy_level = info
all_level = warning
all_hex_limit = 32
filename = /tmp/ue.log
#####################################################################
# USIM configuration
#
# algo: Authentication algorithm (xor/milenage)
# op: 128-bit Operator Variant Algorithm Configuration Field (hex)
# amf: 16-bit Authentication Management Field (hex)
# k: 128-bit subscriber key (hex)
# imsi: 15 digit International Mobile Subscriber Identity
# imei: 15 digit International Mobile Station Equipment Identity
#####################################################################
[usim]
algo = milenage
op = 63BFA50EE6523365FF14C1F45F88737D
amf = 8000
k = 00112233445566778899aabbccddeeff
imsi = 001010123456789
imei = 353490069873319
#####################################################################
# Expert configuration options
#
# prach_gain: PRACH gain (dB). If positive, disables power control
# and fixes PRACH tx gain.
# ul_gain: Uplink gain (dB). If positive, disables power control
# and fixes PUSCH/PUCCH/SRS tx gain.
# ul_pwr_ctrl_offset: Uplink power control offset (dB). Adds an offset
# to all UL gains calculated by power control.
# rx_gain_offset: Receive gain offset (dB). Defines the default receiver
# chain gain used to compute UL power control values if
# RSSI sensor not found. Uses rx gain by default.
# pdsch_max_its: Maximum number of turbo decoder iterations (default 4)
# sync_track_th: Peak-to-sidelobe ratio (PSR) threshold for PSS correlation
# in track phase
# sync_track_avg_coef: Exponential averaging coefficient for PSS correlation in track phase
# sync_find_th: PSR threshold for PSS correlation in find phase
# sync_find_max_frames: Maximum number of frames scanned during cell find phase
# enable_64qam_attach: Enables PUSCH 64QAM modulation before attachment (Necessary for old
# Amarisoft LTE 100 eNodeB, disabled by default)
# continuous_tx: Enable/disable continuous transmission mode (true/false)
# Default disabled.
# nof_phy_threads: Selects the number of PHY threads (maximum 4, minimum 1, default 2)
#####################################################################
[expert]
#prach_gain = 60
#ul_gain = 70
#ul_pwr_ctrl_offset = 0
#rx_gain_offset = 50
#pdsch_max_its = 4
#sync_track_th = 1.3 # must be > 1
#sync_track_avg_coef = 0.1 # must be 0..1
#sync_find_th = 1.6
#sync_find_max_frames = 100
#enable_64qam_attach = false
#continuous_tx = false
#nof_phy_threads = 2