Requesting support for PEHA 451 FU-EBI(M) - EEP D2-01-08 #118

Gulpman · 2024-01-17T14:09:32Z

Gulpman
Jan 17, 2024

Hi,
I am using the above mentioned PEHA 451 FU-EBI(M) actuator.

The following error messages is logged in the HA protocol of HA_enoceanmqtt:

2024-01-17 08:13:25,258 DEBUG: FF:F7:CD:01->FF:FF:FF:FF (-92 dBm): 0x01 ['0xd2', '0x4', '0x60', '0x80', '0xff', '0xf7', '0xcd', '0x1', '0x0'] ['0x1', '0xff', '0xff', '0xff', '0xff', '0x5c', '0x0'] OrderedDict()
2024-01-17 08:13:25,259 INFO: received: FF:F7:CD:01->FF:FF:FF:FF (-92 dBm): 0x01 ['0xd2', '0x4', '0x60', '0x80', '0xff', '0xf7', '0xcd', '0x1', '0x0'] ['0x1', '0xff', '0xff', '0xff', '0xff', '0x5c', '0x0'] OrderedDict()
2024-01-17 08:13:25,259 WARNING: Cannot find rorg 0xd2 func 0x1 type 0x8 in EEP!
2024-01-17 08:13:25,259 WARNING: message not interpretable: enoceanmqtt/bd_Enocean_Repeater
2024-01-17 08:13:25,360 DEBUG: FF:F7:CD:00->FF:FF:FF:FF (-92 dBm): 0x01 ['0xa5', '0x0', '0x0', '0x1', '0x48', '0xff', '0xf7', '0xcd', '0x0', '0x0'] ['0x1', '0xff', '0xff', '0xff', '0xff', '0x5c', '0x0'] OrderedDict()
2024-01-17 08:13:25,360 INFO: received: FF:F7:CD:00->FF:FF:FF:FF (-92 dBm): 0x01 ['0xa5', '0x0', '0x0', '0x1', '0x48', '0xff', '0xf7', '0xcd', '0x0', '0x0'] ['0x1', '0xff', '0xff', '0xff', '0xff', '0x5c', '0x0'] OrderedDict()
2024-01-17 08:13:25,361 INFO: unknown sensor: FF:F7:CD:00

The actuator is defined in enoceanmqtt.conf as following:

[bd_Enocean_Repeater]
address         = 0xFFF7CD01
rorg    		= 0xD2
func    		= 0x01
type    		= 0x08

I do understand that this actuator is not supported yet. Unfortunately, I am somewhat overwhelmed with the implementation.

I searched for eep and D2-01-08 and stumbled upon these documents which may help in the implementation:

Having a look back at the EEP.xml I think support for the switch must somehow be added under

  <telegram rorg="0xD2" type="VLD" description="VLD Telegram">
    <profiles func="0x01" description="Electronic switches and dimmers with Energy Measurement and Local Control">

as somethink like this:

      <profile type="0x08" description="Electronic switch with Energy Measurement and Local Control">
      ...

So here I'm stuck. Is there any chance you could implement support for the D2-01-08 with this information?

Thank you very much in advance.

Best,
Sascha

mak-gitdev · 2024-01-17T14:58:20Z

mak-gitdev
Jan 17, 2024
Maintainer

Hi @Gulpman,

Yes of course, it should not be difficult.
I will have a look.

In the meantime, could you try declaring your device as D2-01-09 ?

Let me know if this work for you.

2 replies

Gulpman Jan 18, 2024
Author

Hi @mak-gitdev ,
thank you for your fast reply.

I set it up as D2-01-09 but unfortunately the relay is not being switched.

Here's the log:

Log out put after restarting the add-on:

2024-01-17 19:59:04,546 DEBUG: Sending SUBSCRIBE (d0, m97) [(b'homeassistant/switch/enocean_D20109_FFF7CD01_NONE_switch/config/#', 0)]
2024-01-17 19:59:04,546 DEBUG: Sending SUBSCRIBE (d0, m98) [(b'enoceanmqtt/bd_Enocean_Repeater/__system/#', 0)]
2024-01-17 19:59:04,553 INFO: Device enoceanmqtt/bd_Enocean_Repeater (UID: D20109_FFF7CD01_NONE / EEP: D2-01-09) updated on device database
2024-01-17 19:59:04,553 DEBUG: List of remaining UIDS: ['D20108_FFF7CD01_NONE']
2024-01-17 19:59:04,554 DEBUG: Sending PUBLISH (d0, q0, r1, m99), 'b'homeassistant/sensor/enocean_D20108_FFF7CD01_NONE_rssi/config'' (NULL payload)
2024-01-17 19:59:04,554 DEBUG: Sending PUBLISH (d0, q0, r1, m100), 'b'homeassistant/sensor/enocean_D20108_FFF7CD01_NONE_last_seen/config'' (NULL payload)
2024-01-17 19:59:04,559 DEBUG: Delete request for sensor enoceanmqtt/bd_Enocean_Repeater (UID D20108_FFF7CD01_NONE): DONE
2024-01-17 19:59:04,580 INFO: Sending packet
2024-01-17 19:59:04,581 DEBUG: 0x05 ['0x8'] [] OrderedDict()
2024-01-17 19:59:04,682 DEBUG: 0x02 ['0x0', '0xff', '0xc8', '0x33', '0x0'] ['0xa'] OrderedDict()
2024-01-17 19:59:04,682 INFO: got response packet: OK

Log for pressing "on" in the HA gui for this sensor:

2024-01-17 20:05:20,992 DEBUG: Received PUBLISH (d0, q0, r0, m0), 'enoceanmqtt/bd_Enocean_Repeater/req', ...  (56 bytes)
2024-01-17 20:05:20,992 DEBUG: Got MQTT message: enoceanmqtt/bd_Enocean_Repeater/req
2024-01-17 20:05:20,992 DEBUG: enoceanmqtt/bd_Enocean_Repeater: req={'CMD': 1, 'DV': 0, 'IO': 0, 'OV': 100}
2024-01-17 20:05:20,992 DEBUG: Trigger message to: enoceanmqtt/bd_Enocean_Repeater
2024-01-17 20:05:20,992 DEBUG: Retrieved command id from MQTT message: 0x1
2024-01-17 20:05:20,993 DEBUG: sensor data: {'CMD': 1, 'DV': 0, 'IO': 0, 'OV': 100}
2024-01-17 20:05:20,994 INFO: sending: FF:C8:33:00->FF:F7:CD:01 (-255 dBm): 0x01 ['0xd2', '0x1', '0x0', '0x64', '0xff', '0xc8', '0x33', '0x0', '0x0'] ['0x3', '0xff', '0xf7', '0xcd', '0x1', '0xff', '0x0'] OrderedDict([('CMD', {'description': 'Command identifier', 'unit': '', 'value': 'Command ID 1', 'raw_value': 1}), ('DV', {'description': 'Dim value', 'unit': '', 'value': 'Switch to new output value', 'raw_value': 0}), ('IO', {'description': 'I/O channel', 'unit': '', 'value': 'Output channel 0 (to load)', 'raw_value': 0}), ('OV', {'description': 'Output value', 'unit': '', 'value': 'Output value 100% or ON', 'raw_value': 100})])
2024-01-17 20:05:20,994 DEBUG: Clearing data buffer.
2024-01-17 20:05:21,009 INFO: Sending packet
2024-01-17 20:05:21,009 DEBUG: FF:C8:33:00->FF:F7:CD:01 (-255 dBm): 0x01 ['0xd2', '0x1', '0x0', '0x64', '0xff', '0xc8', '0x33', '0x0', '0x0'] ['0x3', '0xff', '0xf7', '0xcd', '0x1', '0xff', '0x0'] OrderedDict([('CMD', {'description': 'Command identifier', 'unit': '', 'value': 'Command ID 1', 'raw_value': 1}), ('DV', {'description': 'Dim value', 'unit': '', 'value': 'Switch to new output value', 'raw_value': 0}), ('IO', {'description': 'I/O channel', 'unit': '', 'value': 'Output channel 0 (to load)', 'raw_value': 0}), ('OV', {'description': 'Output value', 'unit': '', 'value': 'Output value 100% or ON', 'raw_value': 100})])
2024-01-17 20:05:21,053 DEBUG: 0x02 ['0x0'] [] OrderedDict()
2024-01-17 20:05:21,054 INFO: got response packet: OK
2024-01-17 20:05:21,154 DEBUG: FF:C8:33:00->FF:F7:CD:01 (-91 dBm): 0x01 ['0xd2', '0x1', '0x0', '0x64', '0xff', '0xc8', '0x33', '0x0', '0x81'] ['0x1', '0xff', '0xf7', '0xcd', '0x1', '0x5b', '0x0'] OrderedDict()
2024-01-17 20:05:21,154 INFO: received: FF:C8:33:00->FF:F7:CD:01 (-91 dBm): 0x01 ['0xd2', '0x1', '0x0', '0x64', '0xff', '0xc8', '0x33', '0x0', '0x81'] ['0x1', '0xff', '0xf7', '0xcd', '0x1', '0x5b', '0x0'] OrderedDict()
2024-01-17 20:05:21,155 INFO: unknown sensor: FF:C8:33:00

I am using it for a socket so no physically attached switch to tell what happens if I use it.
If for further testing it needs to be operated via a switch, I can get it out off the wall and attach a switch for that.

Hope that helped?

Best Sascha

mak-gitdev Jan 18, 2024
Maintainer

Hi @Gulpman,

Did you pair the device with your USB300 ? Without that, impossible to control the device.
Look at this page for more details.

Gulpman · 2024-01-18T15:14:35Z

Gulpman
Jan 18, 2024
Author

Hi @mak-gitdev
thank you for the link. I am currently moving my system from another home automation system to Home Assistant. As my (Enocean) door-window handles were reporting correctly I thought everything was brought over when I added the devices to the config.
So this is what I did now:

Pairing the actor:

2024-01-18 15:57:54,786 INFO: Sending response to UTE teach-in.
2024-01-18 15:57:54,786 DEBUG: FF:F7:CD:01->FF:FF:FF:FF (-80 dBm): 0x01 ['0xd4', '0xa0', '0xff', '0x1', '0x0', '0x8', '0x1', '0xd2', '0xff', '0xf7', '0xcd', '0x1', '0x0'] ['0x1', '0xff', '0xff', '0xff', '0xff', '0x50', '0x0'] OrderedDict()
2024-01-18 15:57:54,787 INFO: Sending packet
2024-01-18 15:57:54,787 DEBUG: FF:C8:33:00->FF:F7:CD:01 (-255 dBm): 0x01 ['0xd4', '0x91', '0xff', '0x1', '0x0', '0x8', '0x1', '0xd2', '0xff', '0xc8', '0x33', '0x0', '0x0'] ['0x3', '0xff', '0xf7', '0xcd', '0x1', '0xff', '0x0'] OrderedDict()
2024-01-18 15:57:54,787 INFO: received: FF:F7:CD:01->FF:FF:FF:FF (-80 dBm): 0x01 ['0xd4', '0xa0', '0xff', '0x1', '0x0', '0x8', '0x1', '0xd2', '0xff', '0xf7', '0xcd', '0x1', '0x0'] ['0x1', '0xff', '0xff', '0xff', '0xff', '0x50', '0x0'] OrderedDict()
2024-01-18 15:57:54,788 INFO: learn request not emitted to mqtt
2024-01-18 15:57:54,818 DEBUG: Sending PINGREQ
2024-01-18 15:57:54,819 DEBUG: Received PINGRESP
2024-01-18 15:57:54,830 DEBUG: 0x02 ['0x0'] [] OrderedDict()
2024-01-18 15:57:54,830 INFO: got response packet: OK
2024-01-18 15:57:54,931 INFO: Sending response to UTE teach-in.
2024-01-18 15:57:54,931 DEBUG: FF:C8:33:00->FF:F7:CD:01 (-80 dBm): 0x01 ['0xd4', '0x91', '0xff', '0x1', '0x0', '0x8', '0x1', '0xd2', '0xff', '0xc8', '0x33', '0x0', '0x81'] ['0x1', '0xff', '0xf7', '0xcd', '0x1', '0x50', '0x0'] OrderedDict()
2024-01-18 15:57:54,932 INFO: received: FF:C8:33:00->FF:F7:CD:01 (-80 dBm): 0x01 ['0xd4', '0x91', '0xff', '0x1', '0x0', '0x8', '0x1', '0xd2', '0xff', '0xc8', '0x33', '0x0', '0x81'] ['0x1', '0xff', '0xf7', '0xcd', '0x1', '0x50', '0x0'] OrderedDict()
2024-01-18 15:57:54,932 INFO: unknown sensor: FF:C8:33:00
2024-01-18 15:57:54,932 INFO: Sending packet
2024-01-18 15:57:54,932 DEBUG: FF:C8:33:00->FF:C8:33:00 (-255 dBm): 0x01 ['0xd4', '0x91', '0xff', '0x1', '0x0', '0x8', '0x1', '0xd2', '0xff', '0xc8', '0x33', '0x0', '0x0'] ['0x3', '0xff', '0xc8', '0x33', '0x0', '0xff', '0x0'] OrderedDict()
2024-01-18 15:57:55,033 DEBUG: 0x02 ['0x0'] [] OrderedDict()
2024-01-18 15:57:55,034 INFO: got response packet: OK
2024-01-18 15:58:54,892 DEBUG: Sending PINGREQ
2024-01-18 15:58:54,894 DEBUG: Received PINGRESP

However regarding the documentation of the PEHA sensor after succesful pairing it should blink red for three seconds, which was not the case.

I tried if the functionality works (after stopping learning mode), by switching the relay from HA and it works. Here's the log:

2024-01-18 16:02:37,465 DEBUG: Received PUBLISH (d0, q0, r0, m0), 'enoceanmqtt/bd_Enocean_Repeater/req', ...  (56 bytes)
2024-01-18 16:02:37,465 DEBUG: Got MQTT message: enoceanmqtt/bd_Enocean_Repeater/req
2024-01-18 16:02:37,465 DEBUG: enoceanmqtt/bd_Enocean_Repeater: req={'CMD': 1, 'DV': 0, 'IO': 0, 'OV': 100}
2024-01-18 16:02:37,465 DEBUG: Trigger message to: enoceanmqtt/bd_Enocean_Repeater
2024-01-18 16:02:37,465 DEBUG: Retrieved command id from MQTT message: 0x1
2024-01-18 16:02:37,466 DEBUG: sensor data: {'CMD': 1, 'DV': 0, 'IO': 0, 'OV': 100}
2024-01-18 16:02:37,467 INFO: sending: FF:C8:33:00->FF:F7:CD:01 (-255 dBm): 0x01 ['0xd2', '0x1', '0x0', '0x64', '0xff', '0xc8', '0x33', '0x0', '0x0'] ['0x3', '0xff', '0xf7', '0xcd', '0x1', '0xff', '0x0'] OrderedDict([('CMD', {'description': 'Command identifier', 'unit': '', 'value': 'Command ID 1', 'raw_value': 1}), ('DV', {'description': 'Dim value', 'unit': '', 'value': 'Switch to new output value', 'raw_value': 0}), ('IO', {'description': 'I/O channel', 'unit': '', 'value': 'Output channel 0 (to load)', 'raw_value': 0}), ('OV', {'description': 'Output value', 'unit': '', 'value': 'Output value 100% or ON', 'raw_value': 100})])
2024-01-18 16:02:37,467 DEBUG: Clearing data buffer.
2024-01-18 16:02:37,528 INFO: Sending packet
2024-01-18 16:02:37,528 DEBUG: FF:C8:33:00->FF:F7:CD:01 (-255 dBm): 0x01 ['0xd2', '0x1', '0x0', '0x64', '0xff', '0xc8', '0x33', '0x0', '0x0'] ['0x3', '0xff', '0xf7', '0xcd', '0x1', '0xff', '0x0'] OrderedDict([('CMD', {'description': 'Command identifier', 'unit': '', 'value': 'Command ID 1', 'raw_value': 1}), ('DV', {'description': 'Dim value', 'unit': '', 'value': 'Switch to new output value', 'raw_value': 0}), ('IO', {'description': 'I/O channel', 'unit': '', 'value': 'Output channel 0 (to load)', 'raw_value': 0}), ('OV', {'description': 'Output value', 'unit': '', 'value': 'Output value 100% or ON', 'raw_value': 100})])
2024-01-18 16:02:37,576 DEBUG: 0x02 ['0x0'] [] OrderedDict()
2024-01-18 16:02:37,576 INFO: got response packet: OK
2024-01-18 16:02:37,608 DEBUG: FF:C8:33:00->FF:F7:CD:01 (-92 dBm): 0x01 ['0xd2', '0x1', '0x0', '0x64', '0xff', '0xc8', '0x33', '0x0', '0x81'] ['0x1', '0xff', '0xf7', '0xcd', '0x1', '0x5c', '0x0'] OrderedDict()
2024-01-18 16:02:37,608 INFO: received: FF:C8:33:00->FF:F7:CD:01 (-92 dBm): 0x01 ['0xd2', '0x1', '0x0', '0x64', '0xff', '0xc8', '0x33', '0x0', '0x81'] ['0x1', '0xff', '0xf7', '0xcd', '0x1', '0x5c', '0x0'] OrderedDict()
2024-01-18 16:02:37,608 INFO: unknown sensor: FF:C8:33:00
2024-01-18 16:02:37,624 DEBUG: FF:F7:CD:01->FF:FF:FF:FF (-92 dBm): 0x01 ['0xd2', '0x4', '0x60', '0xe4', '0xff', '0xf7', '0xcd', '0x1', '0x0'] ['0x1', '0xff', '0xff', '0xff', '0xff', '0x5c', '0x0'] OrderedDict()
2024-01-18 16:02:37,625 INFO: received: FF:F7:CD:01->FF:FF:FF:FF (-92 dBm): 0x01 ['0xd2', '0x4', '0x60', '0xe4', '0xff', '0xf7', '0xcd', '0x1', '0x0'] ['0x1', '0xff', '0xff', '0xff', '0xff', '0x5c', '0x0'] OrderedDict()
2024-01-18 16:02:37,625 DEBUG: Retrieved command id from packet: 0x4
2024-01-18 16:02:37,625 DEBUG: enoceanmqtt/bd_Enocean_Repeater: PF (Power Failure)=Power Failure Detection disabled/not supported 
2024-01-18 16:02:37,626 DEBUG: enoceanmqtt/bd_Enocean_Repeater: PFD (Power Failure Detection)=Power Failure Detection not detected/not supported/disabled 
2024-01-18 16:02:37,626 DEBUG: enoceanmqtt/bd_Enocean_Repeater: CMD (Command identifier)=Command ID 4 
2024-01-18 16:02:37,626 DEBUG: enoceanmqtt/bd_Enocean_Repeater: OC (Over current switch off)=Over current switch off: ready / not supported 
2024-01-18 16:02:37,626 DEBUG: enoceanmqtt/bd_Enocean_Repeater: EL (Error level)=Error level not supported 
2024-01-18 16:02:37,626 DEBUG: enoceanmqtt/bd_Enocean_Repeater: IO (I/O channel)=Output channel 0 (to load) 
2024-01-18 16:02:37,626 DEBUG: enoceanmqtt/bd_Enocean_Repeater: LC (Local control)=Local control enabled 
2024-01-18 16:02:37,626 DEBUG: enoceanmqtt/bd_Enocean_Repeater: OV (Output value)=Output value 100% or ON 
2024-01-18 16:02:37,626 DEBUG: Sending PUBLISH (d0, q0, r1, m236), 'b'enoceanmqtt/bd_Enocean_Repeater'', ... (55 bytes)
2024-01-18 16:02:37,626 DEBUG: enoceanmqtt/bd_Enocean_Repeater/CMD4: Sent MQTT: {"_DATE_": "2024-01-18T16:02:37.624365", "PF": 0, "PFD": 0, "OC": 0, "EL": 3, "IO": 0, "LC": 1, "OV": 100}
2024-01-18 16:02:37,626 DEBUG: Sending PUBLISH (d0, q0, r1, m237), 'b'enoceanmqtt/bd_Enocean_Repeater/CMD4'', ... (106 bytes)
2024-01-18 16:02:37,725 DEBUG: FF:F7:CD:00->FF:FF:FF:FF (-92 dBm): 0x01 ['0xa5', '0xff', '0x0', '0x1', '0x49', '0xff', '0xf7', '0xcd', '0x0', '0x0'] ['0x1', '0xff', '0xff', '0xff', '0xff', '0x5c', '0x0'] OrderedDict()
2024-01-18 16:02:37,726 INFO: received: FF:F7:CD:00->FF:FF:FF:FF (-92 dBm): 0x01 ['0xa5', '0xff', '0x0', '0x1', '0x49', '0xff', '0xf7', '0xcd', '0x0', '0x0'] ['0x1', '0xff', '0xff', '0xff', '0xff', '0x5c', '0x0'] OrderedDict()
2024-01-18 16:02:37,726 INFO: unknown sensor: FF:F7:CD:00
2024-01-18 16:02:45,381 DEBUG: Received PUBLISH (d0, q0, r0, m0), 'enoceanmqtt/bd_Enocean_Repeater/req', ...  (54 bytes)
2024-01-18 16:02:45,381 DEBUG: Got MQTT message: enoceanmqtt/bd_Enocean_Repeater/req
2024-01-18 16:02:45,382 DEBUG: enoceanmqtt/bd_Enocean_Repeater: req={'CMD': 1, 'DV': 0, 'IO': 0, 'OV': 0}
2024-01-18 16:02:45,382 DEBUG: Trigger message to: enoceanmqtt/bd_Enocean_Repeater
2024-01-18 16:02:45,382 DEBUG: Retrieved command id from MQTT message: 0x1
2024-01-18 16:02:45,382 DEBUG: sensor data: {'CMD': 1, 'DV': 0, 'IO': 0, 'OV': 0}
2024-01-18 16:02:45,383 INFO: sending: FF:C8:33:00->FF:F7:CD:01 (-255 dBm): 0x01 ['0xd2', '0x1', '0x0', '0x0', '0xff', '0xc8', '0x33', '0x0', '0x0'] ['0x3', '0xff', '0xf7', '0xcd', '0x1', '0xff', '0x0'] OrderedDict([('CMD', {'description': 'Command identifier', 'unit': '', 'value': 'Command ID 1', 'raw_value': 1}), ('DV', {'description': 'Dim value', 'unit': '', 'value': 'Switch to new output value', 'raw_value': 0}), ('IO', {'description': 'I/O channel', 'unit': '', 'value': 'Output channel 0 (to load)', 'raw_value': 0}), ('OV', {'description': 'Output value', 'unit': '', 'value': 'Output value 0% or OFF', 'raw_value': 0})])
2024-01-18 16:02:45,508 DEBUG: 0x02 ['0x0'] [] OrderedDict()
2024-01-18 16:02:45,508 INFO: got response packet: OK
2024-01-18 16:02:45,539 DEBUG: FF:C8:33:00->FF:F7:CD:01 (-91 dBm): 0x01 ['0xd2', '0x1', '0x0', '0x0', '0xff', '0xc8', '0x33', '0x0', '0x81'] ['0x1', '0xff', '0xf7', '0xcd', '0x1', '0x5b', '0x0'] OrderedDict()
2024-01-18 16:02:45,540 INFO: received: FF:C8:33:00->FF:F7:CD:01 (-91 dBm): 0x01 ['0xd2', '0x1', '0x0', '0x0', '0xff', '0xc8', '0x33', '0x0', '0x81'] ['0x1', '0xff', '0xf7', '0xcd', '0x1', '0x5b', '0x0'] OrderedDict()
2024-01-18 16:02:45,540 INFO: unknown sensor: FF:C8:33:00
2024-01-18 16:02:45,555 DEBUG: FF:F7:CD:01->FF:FF:FF:FF (-91 dBm): 0x01 ['0xd2', '0x4', '0x60', '0x80', '0xff', '0xf7', '0xcd', '0x1', '0x0'] ['0x1', '0xff', '0xff', '0xff', '0xff', '0x5b', '0x0'] OrderedDict()
2024-01-18 16:02:45,556 INFO: received: FF:F7:CD:01->FF:FF:FF:FF (-91 dBm): 0x01 ['0xd2', '0x4', '0x60', '0x80', '0xff', '0xf7', '0xcd', '0x1', '0x0'] ['0x1', '0xff', '0xff', '0xff', '0xff', '0x5b', '0x0'] OrderedDict()
2024-01-18 16:02:45,556 DEBUG: Retrieved command id from packet: 0x4
2024-01-18 16:02:45,557 DEBUG: enoceanmqtt/bd_Enocean_Repeater: PF (Power Failure)=Power Failure Detection disabled/not supported 
2024-01-18 16:02:45,557 DEBUG: enoceanmqtt/bd_Enocean_Repeater: PFD (Power Failure Detection)=Power Failure Detection not detected/not supported/disabled 
2024-01-18 16:02:45,557 DEBUG: enoceanmqtt/bd_Enocean_Repeater: CMD (Command identifier)=Command ID 4 
2024-01-18 16:02:45,557 DEBUG: enoceanmqtt/bd_Enocean_Repeater: OC (Over current switch off)=Over current switch off: ready / not supported 
2024-01-18 16:02:45,557 DEBUG: enoceanmqtt/bd_Enocean_Repeater: EL (Error level)=Error level not supported 
2024-01-18 16:02:45,557 DEBUG: enoceanmqtt/bd_Enocean_Repeater: IO (I/O channel)=Output channel 0 (to load) 
2024-01-18 16:02:45,557 DEBUG: enoceanmqtt/bd_Enocean_Repeater: LC (Local control)=Local control enabled 
2024-01-18 16:02:45,558 DEBUG: enoceanmqtt/bd_Enocean_Repeater: OV (Output value)=Output value 0% or OFF 
2024-01-18 16:02:45,558 DEBUG: Sending PUBLISH (d0, q0, r1, m238), 'b'enoceanmqtt/bd_Enocean_Repeater'', ... (55 bytes)
2024-01-18 16:02:45,558 DEBUG: enoceanmqtt/bd_Enocean_Repeater/CMD4: Sent MQTT: {"_DATE_": "2024-01-18T16:02:45.555779", "PF": 0, "PFD": 0, "OC": 0, "EL": 3, "IO": 0, "LC": 1, "OV": 0}
2024-01-18 16:02:45,558 DEBUG: Sending PUBLISH (d0, q0, r1, m239), 'b'enoceanmqtt/bd_Enocean_Repeater/CMD4'', ... (104 bytes)
2024-01-18 16:02:45,657 DEBUG: FF:F7:CD:00->FF:FF:FF:FF (-91 dBm): 0x01 ['0xa5', '0x0', '0x0', '0x1', '0x48', '0xff', '0xf7', '0xcd', '0x0', '0x0'] ['0x1', '0xff', '0xff', '0xff', '0xff', '0x5b', '0x0'] OrderedDict()
2024-01-18 16:02:45,657 INFO: received: FF:F7:CD:00->FF:FF:FF:FF (-91 dBm): 0x01 ['0xa5', '0x0', '0x0', '0x1', '0x48', '0xff', '0xf7', '0xcd', '0x0', '0x0'] ['0x1', '0xff', '0xff', '0xff', '0xff', '0x5b', '0x0'] OrderedDict()
2024-01-18 16:02:45,657 INFO: unknown sensor: FF:F7:CD:00

So switching on and off basically is working now.

I hope this helps?

Best,
Sascha

2 replies

Gulpman Jan 25, 2024
Author

Hi @mak-gitdev
Any news on this topic? Do I have to do any further testings? I'm not quite sure what I am supposed to do next for the support of the D2-01-08. ':-)

Best,
Sascha

mak-gitdev Jan 25, 2024
Maintainer

Hi @Gulpman,

I think everything is OK for you as switching is working, right ?
I think you are now missing the power consumption feature, right ?
I will later add a wiki page to explain how to set it up.

Gulpman · 2024-04-07T08:07:13Z

Gulpman
Apr 7, 2024
Author

Hi @mak-gitdev y. I thought I already answered this, and just found out I didn't. So my appologize for this.

Yes, the switching functionality is working correctly. My switch does not support power measuring so no need for this (for me) at this time.

As I can see in your Kanban board, D2-01-08 will be supported officially in release 0.1.29? Great!

Thank you very much for your help.

Best,
Sascha

0 replies

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Requesting support for PEHA 451 FU-EBI(M) - EEP D2-01-08 #118

{{title}}

Replies: 3 comments 4 replies

{{title}}

{{title}}

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

Select a reply

Requesting support for PEHA 451 FU-EBI(M) - EEP D2-01-08 #118

Gulpman Jan 17, 2024

Replies: 3 comments · 4 replies

mak-gitdev Jan 17, 2024 Maintainer

Gulpman Jan 18, 2024 Author

mak-gitdev Jan 18, 2024 Maintainer

Gulpman Jan 18, 2024 Author

Gulpman Jan 25, 2024 Author

mak-gitdev Jan 25, 2024 Maintainer

Gulpman Apr 7, 2024 Author

Gulpman
Jan 17, 2024

Replies: 3 comments 4 replies

mak-gitdev
Jan 17, 2024
Maintainer

Gulpman Jan 18, 2024
Author

mak-gitdev Jan 18, 2024
Maintainer

Gulpman
Jan 18, 2024
Author

Gulpman Jan 25, 2024
Author

mak-gitdev Jan 25, 2024
Maintainer

Gulpman
Apr 7, 2024
Author