forked from 1technophile/OpenMQTTGateway
-
Notifications
You must be signed in to change notification settings - Fork 0
/
User_config.h
122 lines (108 loc) · 5.04 KB
/
User_config.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
/*
OpenMQTTGateway - ESP8266 or Arduino program for home automation
Act as a wifi or ethernet gateway between your 433mhz/infrared IR signal and a MQTT broker
Send and receiving command by MQTT
This program enables to:
- receive MQTT data from a topic and send RF 433Mhz signal corresponding to the received MQTT data
- publish MQTT data to a different topic related to received 433Mhz signal
- receive MQTT data from a topic and send IR signal corresponding to the received MQTT data
- publish MQTT data to a different topic related to received IR signal
- publish MQTT data to a different topic related to BLE devices rssi signal
Copyright: (c)Florian ROBERT
This file is part of OpenMQTTGateway.
OpenMQTTGateway is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
OpenMQTTGateway is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
/*----------------------------USER PARAMETERS-----------------------------*/
#define SERIAL_BAUD 115200
/*-------------DEFINE YOUR WIRING TYPE BELOW----------------*/
// Choose between "I2C_Wiring" OR "Classic_Wiring" OR "RFM69_Wiring"
// Please Note: I2C Wiring,Classic Wiring and RFM69_Wiring uses different Pins for all Modules, see PIN definitions into the wiki
//#define I2C_Wiring // With Support for I2C Modules and the associated libraries BH1750 and BME280
//#define RFM69_Wiring // following file img/OpenMQTTGateway_IR_RF_RFM69.png
#define Classic_Wiring // following file img/OpenMQTTGateway_IR_RF_BT.png
/*-------------DEFINE YOUR NETWORK PARAMETERS BELOW----------------*/
//MQTT Parameters definition
#define mqtt_server "192.168.1.17"
//#define mqtt_user "your_username" // not compulsory only if your broker needs authentication
#define mqtt_password "your_password" // not compulsory only if your broker needs authentication
#define mqtt_port 1883
#define Gateway_Name "OpenMQTTGateway"
#define will_Topic "home/OpenMQTTGateway/LWT"
#define will_QoS 0
#define will_Retain true
#define will_Message "Offline"
#define Gateway_AnnouncementMsg "Online"
/*-------------DEFINE YOUR NETWORK PARAMETERS BELOW----------------*/
// Update these with values suitable for your network.
#ifdef ESP8266 // for nodemcu, weemos and esp8266
#define wifi_ssid "wifi ssid"
#define wifi_password "wifi password"
#else // for arduino + W5100
const byte mac[] = { 0xDE, 0xED, 0xBA, 0xFE, 0x54, 0x95 }; //W5100 ethernet shield mac adress
#endif
const byte ip[] = { 192, 168, 1, 99 }; //ip adress
// Advanced network config (optional) if you want to use these parameters uncomment line 158, 172 and comment line 171 of OpenMQTTGateway.ino
const byte gateway[] = { 192, 168, 1, 1 }; //ip adress
const byte Dns[] = { 192, 168, 1, 1 }; //ip adress
const byte subnet[] = { 255, 255, 255, 0 }; //ip adress
/*-------------DEFINE YOUR OTA PARAMETERS BELOW----------------*/
#define ota_hostname "OTAHOSTNAME"
#define ota_password "OTAPASSWORD"
#define ota_port 8266
/*-------------DEFINE THE MODULES YOU WANT BELOW----------------*/
//Addons and module management, comment the Z line and the config file if you don't use
#ifdef ESP8266 // for nodemcu, weemos and esp8266
#define ZsensorDHT
#include "config_DHT.h"
#define ZgatewayRF
#include "config_RF.h"
#define ZgatewayRF2
#ifdef RFM69_Wiring
#define ZgatewayRFM69
#include "config_RFM69.h"
#endif
#define ZgatewayIR
#include "config_IR.h"
#define ZgatewayBT
#include "config_BT.h"
#ifdef I2C_Wiring // to use the sensor below the gateway should wired with I2CWiring, see PIN DEFINITIONS below
#define ZsensorBH1750
#include "config_BH1750.h"
#define ZsensorBME280
#include "config_BME280.h"
#endif
#else // for arduino + W5100
#define ZgatewayRF
#include "config_RF.h"
#define ZgatewayRF2
#ifdef RFM69_Wiring
//#define ZgatewayRFM69 not tested
//#include "config_RFM69.h"
#endif
#define ZgatewayIR
#include "config_IR.h"
#define ZgatewayBT
#include "config_BT.h"
//#define ZsensorDHT
//#include "config_DHT.h"
//#define ZsensorBH1750
//#include "config_BH1750.h"
//#define ZsensorBME280
//#include "config_BME280.h"
#endif/*----------------------------OTHER PARAMETERS-----------------------------*/
/*-------------------CHANGING THEM IS NOT COMPULSORY-----------------------*/
/*--------------MQTT general topics-----------------*/
// global MQTT subject listened by the gateway to execute commands (send RF, IR or others)
#define subjectMQTTtoX "home/commands/#"
#define subjectMultiGTWKey "toMQTT"
/*-------------------ACTIVATE TRACES----------------------*/
#define TRACE 1 // 0= trace off 1 = trace on