| title | layout |
|---|---|
Inventory |
base |
- First aid kit, trauma kit if possible
- Jumper Cables
- Extra water, Ice if possible for heat stroke
- box-wrenches
- ignition wrenches
- socket set
- socket extensions
- Adapter to connect automotive socket to right angle drill
- automotive sockets (for sand-screws)
- breaker bar (1/2 automotive type)
- crescent wrenches (assorted sizes)
- normal hammer
- rubber mallet
- mini-sledge hammer
- screw drivers
- security screw driver bit set
- pliers
- vise grips
- snap ring pliers (for motor retainment rings if necessary)
- allen wrench sets
- box cutter
- Level (should be perminently in tower box)
- measuring tape
- strap wrenches for motor assembly
- scissors
- sheet metal shears
- small hand-mirror on wand (for viewing LED colors on rail-side of rocket)
- tool belt
- philips quick-insert hex bits
- hex bit extensions
- hex bit to socket adaptors (1/4, 3/8, 1/2)
- calipers
- leather work-gloves
- DeWalt Right Angle Drill for driving in sand screws
- 120VAC generator (for generator->tools, needed during tower setup)
- cordless drill (with extra battery and charger)
- saw horses (4)
- Little Giant Ladder
- 75lb digital postal scale (final weight of rocket necessary)
- digital hanging fish scale (final weight of rocket necessary)
- digital jewelers scale
- (3) orange safety cones for top of sand screws
- 100ft Extension cord
- paint pole (for GoPro camera at tower)
- cardboard PSAS sign to post by road
- super-lube, for motor assembly
- fire extinguisher
- shovel (for fire duty)
- hatchet (for brush)
- first aid kit
- 1/8 inch dia dowels, 3-4 ft long, for holding igniters in place in pyros (or small square balsa wood lengths)
- E-matches
- 3-in-1 oil
- WD-40
- electrical tape
- duct tape
- safety glasses
- zip ties
- blue masking tape
- Motor removal 2x4 kit (should be in one of the plastic tubs)
- latex gloves, used during motor assembly/gluing/greesing
- gasoline (if bringing dirt bikes), 5 gallons
- 1/4in or 5/16in dowels, handy for a variety of things...
- big trash bags
- a tarp
- A few Misc 2x4s and 4x4s (just in case)
- card tables and chairs
- narrow string/rope
- ear plugs
- rubber bands
- orbital sander
- dremmel tool
- sae tap/die set
- 4 inch angle grinder
- sawzall
- sand paper
- hand sanding block
- super glue
- 5 min epoxy
- 30 minute epoxy (may be needed for epoxying aerotech motor grains)
- jb-weld
- full drill bit set
- 1/2 inch corded drill
- hack saw
- metal files
- counter sinks
- deburing tool
- lighter
- blast shield
- launch tower tub, which should include at least the following:
- -(3) sets of guy wires
- -(4) sand screws
- launch tower electrical tub
- -With long orange wires for igniter and safety boxes
- -RF feed-line for tower computer to antenna
- tower computer
- 12v batteries for tower computer
- solar panel for tower computer
- antenna bar for tower
- launch rail
- tower top section
- tower bottom section
- tower base
- Ropes and pulleys and such to raise and lower the rail
- Launch rail teather to rocket
- Umbilical Bar
- high-visibility coverings for guy-wires
- Motor Casing
- Forward and Aft Closures
- Main fuel grains
- Smoke Grain
- O-rings
- Special motor tools, if necessary
- Igniters
- 1/8 inch dowels
- Grain removial 2x4
- Plastic trash bag for burned liner (it smells really bad)
- Dell LCD Monitor w/ S-Video and composite input (with external power supply)
- JTAG adaptor
- USB Cables
- USB hub w/ power supply and mini-usb cable
- Multi Meter
- Soldering Iron
- Resistor assortment
- 12volt to 120VAC inverter w/ 12v battery clamps
- 120vac to multi-voltage output AC wall wart adapters (2)
- car usb charger
- 12v car battery, if available
- 4 channel Agelent Oscilloscope
- AA batteries
- AAA batteries
- D batteries
- 9v Batteries
- Roll Control launch detect shorting tether.
- Opal docking station and FTDI cable.
- TeleMetrum receive cable and antenna (multiple okay)
- ARTS data cable (LEDs, USB Serial Adaptor)
- screw/nut/bolt assortments
- Binoculars
- 1200fps camera