Skip to content

Latest commit

 

History

History
356 lines (315 loc) · 12.8 KB

PartsList.md

File metadata and controls

356 lines (315 loc) · 12.8 KB

PARTS LIST

PixelRadio is a FM Radio Transmitter with RDS (Radio Data System) capabilities. It was developed for holiday "Pixel" displays (e.g., animated Christmas lights).

This document is the Project's Bill of Materials. Any mentioned component suppliers are for your convenience. Please feel free to use your favorite supplier.

The project's creator is NOT affiliated with any vendor. The provided sources include many of the suppliers used in author's original build. That said, they are only suggestions and are to be purchased at your own risk.

THE FINE PRINT

All information is provided as-is. YOU must accept all responsibility for the construction and use of the project.


Important Notes: Most of the parts have similar looking variants that may not be compatible with the project. Therefore, consult the photos shown below to confirm you are buying the exact item needed.

Fatherly Advice: Many of the electronic components are very low cost, so it is highly recommended to add a spare to your order in case of electrical "accidents."

   


COMPONENT BILL OF MATERIALS

QTY DESIGNATOR VALUE DESCRIPTION
1 ANT1 F-CON Right Angle PCB F-Connector
1 ANT1-WHIP Antenna 76cm Telescoping Rod Antenna with F-Connector
7 C1, C4, C5, C11, C16, C17, C20 0.1uF 50V Monolithic Ceramic (MLCC) Capacitor
3 C2, C15, C19 470uF 16V Electrolytic Capacitor, Radial
1 C3 100uF 16V Electrolytic Capacitor, Radial
2 C8, C9 4.7uF 16V Electrolytic Capacitor, Radial
1 C10 0.01uF 50V Ceramic Disc or Mono Ceramic Capacitor
1 C14 1000uF 16V Electrolytic Capacitor, Radial
2 C26, C33 1000pF 50V Ceramic Disc Capacitor, type C0G (NP0)
3 C27, C28, C31 NA Not Installed
3 C29, C32, C34 220pF 50V Ceramic Disc Capacitor, type C0G (NP0)
1 D1 1N5819 1A Schottky Diode, DO-41
7 J1, J2, J3, J4, J5, J7, J8 PCB PADS Solder Pads, Leave Empty
1 J9 HDR2P Use 2-Pin 0.1" Header or Wire Jumper
1 P1 ESP32 VBAT Cable 2-PIN Cable (included with ESP32)
1 P2 PJ307 PJ307 or SJ-3525 3.5mm 5-Pin Audio Jack
1 P3 DC-005 DC Power Jack, PCB Mount 2.1mm x 5.5m DC Power Jack, 3-Terminal
4 L1, L2, L6, L8 390nH (0.39uH) RF Inductor, 0.25W, >100mA
1 L5 10uH RF Inductor, 0.25W, >100mA
1 L7 JUMPER Wire Bridge
1 LED1 GREEN 3mm Green LED
1 MCU1 ESP32 (TTGO-T8) LilyGo TTGO-T8-ESP32 MCU, V1.7.1
1 Q1 2N7000P N-Channel FET, TO-92
1 Q2 IRLZ24NPbF HEXFET Transistor, TO-220AB
2 Q5, Q6 S9018 NPN RF Transistor
1 QN8027_MODULE QN8027 9-Pin Module QN8027 RF Transmitter Module
1 R1 470 1/8W 5% Resistor
5 R2, R3, R11, R13, R15 10K 1/8W 5% Resistor
2 R4, R5 N/A Not installed
2 R8, R12 100K 1/8W 5% Resistor
1 R9 33K 1/8W 5% Resistor
2 R16, R17 22K 1/8W 5% Resistor
2 R25, R27 47K 1/8W 5% Resistor
1 R26 150 1/8W 5% Resistor
1 U1 CD4052BE CMOS Analog MUX IC, 16P DIP
1 U2 L7805CV 5.0V 1A Voltage Regulator, TO-220
1 U3 L7809CV 9.0V 1A Voltage Regulator, TO-220
1 12VDC Supply 12V / 1 Amp Regulated Power Supply Use 2 Amp if "On-Air" Sign is installed

   


MODULE INFO

PASSIVE COMPONENT INFO

SEMICONDUCTOR INFO

MECHANICAL INFO