IOIO Application Protocol

The IOIO Board uses multiple protocols to communicate with a control device.

There is the hardware protocol layer, ie using the Bluetooth device or a USB connection.

Above that, there will be framing for that protocol - over Bluetooth it uses a UART emulated connection. Over USB it can use various Android defined protocols.

Above that is the IOIO Application Protocol which allows an application running on the control device to access the pins and commands of the IOIO. This IOIO Application Protocol does not consist of any framing, all communication packets contain commands and parameters - the length of the parameter data is determined by the command being used. These protocols are defined in the protocol_defs.h file in the repository. IOIO Protocol Definitions.

Many communication packets do not have a response - an application must provide it's own sanity checking to see if commands.

Firmware Command		Hex	Integer	Parameter Format	Result Expected	Notes	Java Call	Javascript Call	Python Call	PHP Call
HARD_RESET	0x00	tbd	tbd	tbd	tbd	tbd	tbd	tbd
ESTABLISH_CONNECTION	0x00	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SOFT_RESET	0x01	tbd	tbd	tbd	tbd	tbd	tbd	tbd
CHECK_INTERFACE	0x02	tbd	tbd	tbd	tbd	tbd	tbd	tbd
CHECK_INTERFACE_RESPONSE	0x02	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SET_PIN_DIGITAL_OUT	0x03	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SET_DIGITAL_OUT_LEVEL	0x04	tbd	tbd	tbd	tbd	tbd	tbd	tbd
REPORT_DIGITAL_IN_STATUS	0x04	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SET_PIN_DIGITAL_IN	0x05	tbd	tbd	tbd	tbd	tbd	tbd	tbd
REPORT_PERIODIC_DIGITAL_IN_STATUS	0x05	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SET_CHANGE_NOTIFY	0x06	tbd	tbd	tbd	tbd	tbd	tbd	tbd
REGISTER_PERIODIC_DIGITAL_SAMPLING	0x07	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SET_PIN_PWM	0x08	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SET_PWM_DUTY_CYCLE	0x09	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SET_PWM_PERIOD	0x0A	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SET_PIN_ANALOG_IN	0x0B	tbd	tbd	tbd	tbd	tbd	tbd	tbd
REPORT_ANALOG_IN_STATUS	0x0B	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SET_ANALOG_IN_SAMPLING	0x0C	tbd	tbd	tbd	tbd	tbd	tbd	tbd
REPORT_ANALOG_IN_FORMAT	0x0C	tbd	tbd	tbd	tbd	tbd	tbd	tbd
UART_CONFIG	0x0D	tbd	tbd	tbd	tbd	tbd	tbd	tbd
UART_STATUS	0x0D	tbd	tbd	tbd	tbd	tbd	tbd	tbd
UART_DATA	0x0E	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SET_PIN_UART	0x0F	tbd	tbd	tbd	tbd	tbd	tbd	tbd
UART_REPORT_TX_STATUS	0x0F	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SPI_CONFIGURE_MASTER	0x10	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SPI_STATUS	0x10	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SPI_MASTER_REQUEST	0x11	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SPI_DATA	0x11	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SET_PIN_SPI	0x12	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SPI_REPORT_TX_STATUS	0x12	tbd	tbd	tbd	tbd	tbd	tbd	tbd
I2C_CONFIGURE_MASTER	0x13	tbd	tbd	tbd	tbd	tbd	tbd	tbd
I2C_STATUS	0x13	tbd	tbd	tbd	tbd	tbd	tbd	tbd
I2C_WRITE_READ	0x14	tbd	tbd	tbd	tbd	tbd	tbd	tbd
I2C_RESULT	0x14	tbd	tbd	tbd	tbd	tbd	tbd	tbd
I2C_REPORT_TX_STATUS	0x15	tbd	tbd	tbd	tbd	tbd	tbd	tbd
ICSP_SIX	0x16	tbd	tbd	tbd	tbd	tbd	tbd	tbd
ICSP_REPORT_RX_STATUS	0x16	tbd	tbd	tbd	tbd	tbd	tbd	tbd
ICSP_REGOUT	0x17	tbd	tbd	tbd	tbd	tbd	tbd	tbd
ICSP_RESULT	0x17	tbd	tbd	tbd	tbd	tbd	tbd	tbd
ICSP_PROG_ENTER	0x18	tbd	tbd	tbd	tbd	tbd	tbd	tbd
ICSP_PROG_EXIT	0x19	tbd	tbd	tbd	tbd	tbd	tbd	tbd
ICSP_CONFIG	0x1A	tbd	tbd	tbd	tbd	tbd	tbd	tbd
INCAP_CONFIG	0x1B	tbd	tbd	tbd	tbd	tbd	tbd	tbd
INCAP_STATUS	0x1B	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SET_PIN_INCAP	0x1C	tbd	tbd	tbd	tbd	tbd	tbd	tbd
INCAP_REPORT	0x1C	tbd	tbd	tbd	tbd	tbd	tbd	tbd
SOFT_CLOSE	0x1D	tbd	tbd	tbd	tbd	tbd	tbd	tbd