Software for the Met4FoF Smartup Unit V2

See this publication as well

Setup

1. Download this repo

2. install Python dependencies [add needed deps]

   pip install protobuf

3. Flash the µC with the newest release [see this link] (doc/flash_stm32_fimware.md)

4. Connect µC and PC directly via Lan (or over an switch with DHCP anabled to 192.168.2.x Subnet)

5. In case you are working behind a firewall, set an exception for incoming UDP packets from the IP address of the Smartup Unit on port 7654.

6. Set ip Adress of pc to 192.168.0.200

7. Power on µC Board

8. Observe Display and LEDS see Picture

9. Start Python Interpreter and run /tools/MET4FOFDataReceiver.py

10. Start data Receiver node with:

    DR=DataReceiver("192.168.0.200",7654)

If every thing works correctly you will see that a new sensor is found

Data receiver now running wating for packets 
FOUND NEW SENSOR WITH ID=hex0x37300000==>dec:925892608

Attach your callback function to Sensor

DR.AllSensors[925892608].SetCallback(DumpDataMPU9250)

Misc

Build System.

The software was and is created with SW4STM32 (gcc). SEGGER Systemview can be used for debugging.

Dependencies and used libraries

Used for	Library Name	Version	Link
real-time operating system	FreeRTOS	9.0.0	https://www.freertos.org/FreeRTOS-V9.html
Ethernet	LWIP	2.0.3	ST DM00103685
Data serialization	nanopb	a2db482...	https://github.com/nanopb/nanopb

using nanopb to generate Code

C

see also https://jpa.kapsi.fi/nanopb/docs/ and https://github.com/nanopb/nanopb/blob/master/docs/concepts.rst

cd nanopb/
mkdir messages
cp ../protobuff_deps/messages.proto messages/
cp generator/proto/nanopb.proto ./
protoc -I=generator/proto -I=messages -I=. --proto_path=generator/proto/google/protobuf --proto_path=generator/proto/nanopb --proto_path=generator/proto -o message.pb messages/messages.proto
python generator/nanopb_generator.py message.pb
cp message.* ../protobuff_deps/
cd ./generator/proto
make

python

https://developers.google.com/protocol-buffers/docs/pythontutorial

cd nanopb/
mkdir ../protobuff_deps/python
protoc -I=generator/proto -I=messages -I=. --proto_path=generator/proto/google/protobuf --proto_path=generator/proto/nanopb --proto_path=generator/proto --python_out=../protobuff_deps/python/  messages/messages.proto

Converting St-Link to Segger J-link

https://www.segger.com/products/debug-probes/j-link/models/other-j-links/st-link-on-board/ Download software extract and run STLinkReflash.exe

1. Accept Segger license
2. Accept ST license
3. Choose Upgrade to J-Link [1] The device is flashed and reconnected Output looks like

Preparing for FW update (can take up to 10 seconds)...O.K.
Identifying ST-LINK variant...O.K.: ST-LINK/V2-1
Performing firmware update...O.K.

now you have an working J-Link at your STM32-Board.

Debug Output

https://www.segger.com/products/debug-probes/j-link/technology/about-real-time-transfer/

https://mcuoneclipse.com/2015/07/07/using-segger-real-time-terminal-rtt-with-eclipse/

Telnet Config for RTT dumping

Param	Value
Host	127.0.0.1
Timeout	20 sec
Port	19021