stm32/WEACT_F411: Add WeAct F411 'blackpill' boards.

Builds for v3.1 with no SPI Flash by default.
Includes variants for different board versions and spi flash sizes.

Signed-off-by: Andrew Leech <[email protected]>

ports/stm32/boards/WEACT_F411_BLACKPILL/README.md

@@ -0,0 +1,49 @@
+WeAct F411 'blackpill'
+======================
+
+The WeAct F411 blackpill board comes in a number of versions and variants. 
+All have a footprint for a SPI flash chip on the back, though the board is 
+often sold without any flash chip loaded.
+
+At the time of writing (Sep 2024) v3.1 is the current version.  
+This version is sold with both 25Mhz HSE crystal (same as previous versions) and also
+with a 8Mhz crystal. The end user should be careful to confirm which variant is 
+purchased and/or read the markings on the crystal to know which variant build to load.
+
+The previous v2.0 boards had changed the MCU pinout for the spi flash chip so requires soft-spi support enabled in the variant settings, unlike v3.1 or v1.3 which is
+compatible with the hardware spi peripheral.
+
+The original v1.3 boards did not include a user switch on the top, it only has 
+"BOOT0" and "NRST" switches to load bootloader and reset the board respectively.
+
+
+For more information see: https://github.com/WeActStudio/WeActStudio.MiniSTM32F4x1
+
+Customising the build
+---------------------
+
+After purchasing a board without any spiflash chip loaded the user can solder on
+their own of any desired size. Most brands of spiflash in SO8 pinout are compatible
+however some do have a slightly different protocol so may not work out of the box 
+with micropython. Brand compatibility is outide the scope of this doc.
+
+Once a custom spiflash chip has been loaded onto the board micropython should
+be built with the flash size specified. After doing so the spiflash chip will 
+be used for the FAT/LFS main filesystem.
+
+Examples:
+
+For a v3.1 / 25Mhz (default version) board with 16MiB flash chip loaded:
+``` bash
+make -C ports/stm32 BOARD=WEACT_F411_BLACKPILL SPI_FLASH_SIZE_MB=16
+```
+
+For a v3.1 / 8Mhz board with 4MiB flash chip loaded:
+``` bash
+make -C ports/stm32 BOARD=WEACT_F411_BLACKPILL BOARD_VARIANT=V31_XTAL_8M SPI_FLASH_SIZE_MB=4
+```
+
+For a v1.3 board with 2MiB flash chip loaded and XTAL manually replaced with 8Mhz:
+``` bash
+make -C ports/stm32 BOARD=WEACT_F411_BLACKPILL BOARD_VARIANT=V13 SPI_FLASH_SIZE_MB=2 XTAL_FREQ_MHZ=8
+```

ports/stm32/boards/WEACT_F411_BLACKPILL/bdev.c

@@ -0,0 +1,45 @@
+#include "storage.h"
+#include "spi.h"
+#include "py/mpconfig.h"
+
+#if !MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE
+
+#if WEACT_F411_V20
+// External SPI flash uses SPI interface, but not on all HW spi pins.
+static const mp_soft_spi_obj_t spi_bus = {
+    .delay_half = MICROPY_HW_SOFTSPI_MIN_DELAY,
+    .polarity = 0,
+    .phase = 0,
+    .sck = MICROPY_HW_SPIFLASH_SCK,
+    .mosi = MICROPY_HW_SPIFLASH_MOSI,
+    .miso = MICROPY_HW_SPIFLASH_MISO,
+};
+
+#else // WEACT_F411_V1.3 or WEACT_F411_V3.1
+static const spi_proto_cfg_t spi_bus = {
+    .spi = &spi_obj[0], // SPI1
+    .baudrate = 25000000,
+    .polarity = 0,
+    .phase = 0,
+    .bits = 8,
+    .firstbit = SPI_FIRSTBIT_MSB,
+};
+#endif
+
+#if MICROPY_HW_SPIFLASH_ENABLE_CACHE
+static mp_spiflash_cache_t spi_bdev_cache;
+#endif
+
+const mp_spiflash_config_t spiflash_config = {
+    .bus_kind = MP_SPIFLASH_BUS_SPI,
+    .bus.u_spi.cs = MICROPY_HW_SPIFLASH_CS,
+    .bus.u_spi.data = (void *)&spi_bus,
+    .bus.u_spi.proto = &spi_proto,
+    #if MICROPY_HW_SPIFLASH_ENABLE_CACHE
+    .cache = &spi_bdev_cache,
+    #endif
+};
+
+spi_bdev_t spi_bdev;
+
+#endif

ports/stm32/boards/WEACT_F411_BLACKPILL/board.json

@@ -0,0 +1,22 @@
+{
+    "deploy": [
+        "../PYBV10/deploy.md"
+    ],
+    "docs": "",
+    "features": [],
+    "images": [
+        "WEACTV20_F411.jpg"
+    ],
+    "mcu": "stm32f411",
+    "product": "WeAct F411 'blackpill'. Default variant is v3.1 with no SPI Flash.",
+    "thumbnail": "",
+    "url": "https://github.com/WeActStudio/WeActStudio.MiniSTM32F4x1",
+    "variants": {
+        "V13": "v1.3 board with no SPI Flash",
+        "V13_FLASH_4M": "v1.3 board with 4MB SPI Flash",
+        "V20_FLASH_4M": "v2.0 board with 4MB SPI Flash",
+        "V31_FLASH_8M": "v3.1 board with 8MB SPI Flash",
+        "V31_XTAL_8M": "v3.1 board with 8MHz crystal"
+    },
+    "vendor": "WeAct Studio"
+}

ports/stm32/boards/WEACT_F411_BLACKPILL/mpconfigboard.h

@@ -0,0 +1,120 @@
+// based off the following two repositories:
+// * https://github.com/mcauser/WEACT_F411CEU6
+// * https://github.com/YXZhu/micropython
+
+#define MICROPY_HW_BOARD_NAME       "WEACT_F411_BLACKPILL"
+#define MICROPY_HW_MCU_NAME         "STM32F411CE"
+#define MICROPY_HW_FLASH_FS_LABEL   "WEACT_F411_BLACKPILL"
+
+// some users having issues with FLASH_LATENCY_2, so set to 3
+// from https://forum.micropython.org/viewtopic.php?t=7154
+#define MICROPY_HW_FLASH_LATENCY    FLASH_LATENCY_3
+
+#if WEACT_F411_V13
+#define MICROPY_HW_HAS_SWITCH       (0)
+#else
+#define MICROPY_HW_HAS_SWITCH       (1)
+#endif
+#define MICROPY_HW_HAS_FLASH        (1)
+#define MICROPY_HW_ENABLE_RTC       (1)
+#define MICROPY_HW_ENABLE_USB       (1)
+
+#ifndef MICROPY_HW_HSE_SPEED_MHZ
+// Default HSE is 25MHz, divide down to 1mhz in PLL
+#define MICROPY_HW_CLK_PLLM (25)
+#else
+// Set PLLM same as HSE in MHZ.
+#define MICROPY_HW_CLK_PLLM (MICROPY_HW_HSE_SPEED_MHZ)
+#endif
+// Configure PLL for final CPU freq of 96MHz
+#define MICROPY_HW_CLK_PLLN (192)
+#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
+#define MICROPY_HW_CLK_PLLQ (4)
+
+// UART config
+#define MICROPY_HW_UART1_TX     (pin_A9)
+#define MICROPY_HW_UART1_RX     (pin_A10)
+
+#define MICROPY_HW_UART2_TX     (pin_A2)
+#define MICROPY_HW_UART2_RX     (pin_A3)
+
+#define MICROPY_HW_UART_REPL        (PYB_UART_1)
+#define MICROPY_HW_UART_REPL_BAUD   (115200)
+
+// I2C bus
+#define MICROPY_HW_I2C1_SCL (pin_B6)
+#define MICROPY_HW_I2C1_SDA (pin_B7)
+#define MICROPY_HW_I2C2_SCL (pin_B10)
+#define MICROPY_HW_I2C2_SDA (pin_B9)
+#define MICROPY_HW_I2C3_SCL (pin_A8)
+#define MICROPY_HW_I2C3_SDA (pin_B8)
+
+// SPI bus
+// SPI 1 is generally used for the SPI flash if enabled below.
+#define MICROPY_HW_SPI1_NSS     (pin_A4)
+#define MICROPY_HW_SPI1_SCK     (pin_A5)
+#define MICROPY_HW_SPI1_MISO    (pin_A6)
+#define MICROPY_HW_SPI1_MOSI    (pin_A7)
+
+#define MICROPY_HW_SPI2_NSS     (pin_B12)
+#define MICROPY_HW_SPI2_SCK     (pin_B13)
+#define MICROPY_HW_SPI2_MISO    (pin_B14)
+#define MICROPY_HW_SPI2_MOSI    (pin_B15)
+
+// SPI 3 is not accessible if SPI flash module is used on V2.0 (PB4 conflict)
+#define MICROPY_HW_SPI3_NSS     (pin_A15)
+#define MICROPY_HW_SPI3_SCK     (pin_B3)
+#define MICROPY_HW_SPI3_MISO    (pin_B4)
+#define MICROPY_HW_SPI3_MOSI    (pin_B5)
+
+// Switch
+#if !WEACT_F411_V13
+#define MICROPY_HW_USRSW_PIN        (pyb_pin_SW)
+#define MICROPY_HW_USRSW_PULL       (GPIO_PULLUP)
+#define MICROPY_HW_USRSW_EXTI_MODE  (GPIO_MODE_IT_FALLING)
+#define MICROPY_HW_USRSW_PRESSED    (0)
+#endif
+
+// LEDs
+#define MICROPY_HW_LED1             (pyb_pin_LED_BLUE)
+#define MICROPY_HW_LED_ON(pin)      (mp_hal_pin_low(pin))
+#define MICROPY_HW_LED_OFF(pin)     (mp_hal_pin_high(pin))
+
+#define MICROPY_HW_RTC_USE_LSE      (1)
+#define MICROPY_HW_RTC_USE_US       (0)
+#define MICROPY_HW_RTC_USE_CALOUT   (1)
+
+// External SPI Flash configuration
+
+#if !MICROPY_HW_SPIFLASH_SIZE_BYTES
+// Use internal filesystem if spiflash not enabled.
+#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (1)
+
+#else
+// Disable internal filesystem to use spiflash.
+#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0)
+
+// SPI flash pins
+#define MICROPY_HW_SPIFLASH_CS          (pyb_pin_FLASH_CS)
+#define MICROPY_HW_SPIFLASH_SCK         (pyb_pin_FLASH_SCK)
+#define MICROPY_HW_SPIFLASH_MOSI        (pyb_pin_FLASH_MOSI)
+#if WEACT_F411_V13
+#define MICROPY_HW_SPIFLASH_MISO        (pyb_pin_FLASH_MISO_V13)
+#elif WEACT_F411_V20
+#define MICROPY_HW_SPIFLASH_MISO        (pyb_pin_FLASH_MISO_V20)
+#else
+#define MICROPY_HW_SPIFLASH_MISO        (pyb_pin_FLASH_MISO_V31)
+#endif
+
+extern const struct _mp_spiflash_config_t spiflash_config;
+extern struct _spi_bdev_t spi_bdev;
+#define MICROPY_HW_SPIFLASH_ENABLE_CACHE (1)
+#define MICROPY_HW_BDEV_SPIFLASH    (&spi_bdev)
+#define MICROPY_HW_BDEV_SPIFLASH_CONFIG (&spiflash_config)
+#define MICROPY_HW_BDEV_SPIFLASH_SIZE_BYTES (MICROPY_HW_SPIFLASH_SIZE_BITS / 8)
+#define MICROPY_HW_BDEV_SPIFLASH_EXTENDED (&spi_bdev) // for extended block protocol
+#define MICROPY_HW_SPIFLASH_SIZE_BITS (MICROPY_HW_SPIFLASH_SIZE_BYTES * 8)
+#endif
+
+// USB config
+#define MICROPY_HW_USB_FS (1)

ports/stm32/boards/WEACT_F411_BLACKPILL/mpconfigboard.mk

@@ -0,0 +1,26 @@
+MCU_SERIES = f4
+CMSIS_MCU = STM32F411xE
+AF_FILE = boards/stm32f411_af.csv
+LD_FILES = boards/stm32f411.ld boards/common_ifs.ld
+TEXT0_ADDR = 0x08000000
+TEXT1_ADDR = 0x08020000
+
+MICROPY_VFS_LFS2 = 1
+
+# Settings for spi flash and HSE xtal.
+
+ifdef SPI_FLASH_SIZE_MB
+# Add flash size to build folder name if set from command line
+BUILD := $(BUILD)_FLASH_$(SPI_FLASH_SIZE_MB)M
+endif
+
+ifdef XTAL_FREQ_MHZ
+# Add xtal speed to build folder name if set from command line
+BUILD := $(BUILD)_XTAL_$(XTAL_FREQ_MHZ)M
+endif
+
+SPI_FLASH_SIZE_MB ?= 0
+XTAL_FREQ_MHZ ?= 25
+
+CFLAGS += -DMICROPY_HW_SPIFLASH_SIZE_BYTES="($(SPI_FLASH_SIZE_MB) * 1024 * 1024)"
+CFLAGS += -DMICROPY_HW_HSE_SPEED_MHZ=$(XTAL_FREQ_MHZ)

ports/stm32/boards/WEACT_F411_BLACKPILL/mpconfigvariant_V13.mk

@@ -0,0 +1 @@
+CFLAGS += -DWEACT_F411_V13=1

ports/stm32/boards/WEACT_F411_BLACKPILL/mpconfigvariant_V13_FLASH_4M.mk

@@ -0,0 +1,2 @@
+CFLAGS += -DWEACT_F411_V13=1
+SPI_FLASH_SIZE_MB = 4

ports/stm32/boards/WEACT_F411_BLACKPILL/mpconfigvariant_V20_FLASH_4M.mk

@@ -0,0 +1,2 @@
+CFLAGS += -DWEACT_F411_V20=1
+SPI_FLASH_SIZE_MB = 4

ports/stm32/boards/WEACT_F411_BLACKPILL/mpconfigvariant_V31_FLASH_8M.mk

@@ -0,0 +1,2 @@
+CFLAGS += -DWEACT_F411_V31=1
+SPI_FLASH_SIZE_MB = 8

ports/stm32/boards/WEACT_F411_BLACKPILL/mpconfigvariant_V31_XTAL_8M.mk

@@ -0,0 +1,2 @@
+CFLAGS += -DWEACT_F411_V31=1
+XTAL_FREQ_MHZ = 8

ports/stm32/boards/WEACT_F411_BLACKPILL/pins.csv

@@ -0,0 +1,45 @@
+,PA0
+,PA1
+,PA2
+,PA3
+,PA4
+,PA5
+,PA6
+,PA7
+,PA8
+,PA9
+,PA10
+,PA11
+,PA12
+,PA15
+,PB0
+,PB1
+,PB2
+,PB3
+,PB4
+,PB5
+,PB6
+,PB7
+,PB8
+,PB9
+,PB10
+,PB12
+,PB13
+,PB14
+,PB15
+,PC14
+,PC15
+LED_BLUE,PC13
+SW,PA0
+-SWDIO,PA13
+-SWCLK,PA14
+-OSC32_IN,PH0
+-OSC32_OUT,PH1
+-USB_DM,PA11
+-USB_DP,PA12
+-FLASH_CS,PA4
+-FLASH_SCK,PA5
+-FLASH_MOSI,PA7
+-FLASH_MISO_V13,PA6
+-FLASH_MISO_V20,PB4
+-FLASH_MISO_V31,PA6

ports/stm32/boards/WEACT_F411_BLACKPILL/stm32f4xx_hal_conf.h

@@ -0,0 +1,23 @@
+/* This file is part of the MicroPython project, http://micropython.org/
+ * The MIT License (MIT)
+ * Copyright (c) 2024 Andrew Leech
+ */
+#ifndef MICROPY_INCLUDED_STM32F4XX_HAL_CONF_H
+#define MICROPY_INCLUDED_STM32F4XX_HAL_CONF_H
+
+#include "boards/stm32f4xx_hal_conf_base.h"
+
+// Oscillator values in Hz
+#if (MICROPY_HW_HSE_SPEED_MHZ)
+#define HSE_VALUE (MICROPY_HW_HSE_SPEED_MHZ * 1000000)
+#else
+#define HSE_VALUE (25000000)
+#endif
+#define LSE_VALUE (32768)
+#define EXTERNAL_CLOCK_VALUE (12288000)
+
+// Oscillator timeouts in ms
+#define HSE_STARTUP_TIMEOUT (100)
+#define LSE_STARTUP_TIMEOUT (5000)
+
+#endif // MICROPY_INCLUDED_STM32F4XX_HAL_CONF_H