WireGuard Easy

You have found the easiest way to install & manage WireGuard on any Linux host!

Features

• All-in-one: WireGuard + Web UI.
• Easy installation, simple to use.
• List, create, edit, delete, enable & disable clients.
• Show a client's QR code.
• Download a client's configuration file.
• Statistics for which clients are connected.
• Tx/Rx charts for each connected client.
• Gravatar support.
• Automatic Light / Dark Mode
• Sessionless HTTP API authentication

Requirements

• A host with a kernel that supports WireGuard (all modern kernels).
• A host with Docker installed.

Installation

1. Install Docker

If you haven't installed Docker yet, install it by running:

$ curl -sSL https://get.docker.com | sh
$ sudo usermod -aG docker $(whoami)
$ exit

And log in again.

2. Run WireGuard Easy

To automatically install & run wg-easy, simply run:

$ docker run -d \
  --name=wg-easy \
  -e WG_HOST=🚨YOUR_SERVER_IP \
  -e PASSWORD=🚨YOUR_ADMIN_PASSWORD \
  -v ~/.wg-easy:/etc/wireguard \
  -p 51820:51820/udp \
  -p 51821:51821/tcp \
  --cap-add=NET_ADMIN \
  --cap-add=SYS_MODULE \
  --sysctl="net.ipv4.conf.all.src_valid_mark=1" \
  --sysctl="net.ipv4.ip_forward=1" \
  --restart unless-stopped \
  ghcr.io/wg-easy/wg-easy

💡 Replace YOUR_SERVER_IP with your WAN IP, or a Dynamic DNS hostname.

💡 Replace YOUR_ADMIN_PASSWORD with a password to log in on the Web UI.

The Web UI will now be available on http://0.0.0.0:51821.

💡 Your configuration files will be saved in ~/.wg-easy

3. Sponsor

Are you enjoying this project? Buy Emile a beer! 🍻

Options

These options can be configured by setting environment variables using -e KEY="VALUE" in the docker run command.

Env	Default	Example	Description
PORT	51821	6789	TCP port for Web UI.
WEBUI_HOST	0.0.0.0	localhost	IP address web UI binds to.
PASSWORD	-	foobar123	When set, requires a password when logging in to the Web UI.
WG_HOST	-	vpn.myserver.com	The public hostname of your VPN server.
WG_DEVICE	eth0	ens6f0	Ethernet device the wireguard traffic should be forwarded through.
WG_PORT	51820	12345	The public UDP port of your VPN server. WireGuard will always listen on 51820 inside the Docker container.
WG_MTU	null	1420	The MTU the clients will use. Server uses default WG MTU.
WG_PERSISTENT_KEEPALIVE	0	25	Value in seconds to keep the "connection" open. If this value is 0, then connections won't be kept alive.
WG_DEFAULT_ADDRESS	10.8.0.x	10.6.0.x	Clients IP address range.
WG_DEFAULT_DNS	1.1.1.1	8.8.8.8, 8.8.4.4	DNS server clients will use.
WG_ALLOWED_IPS	0.0.0.0/0, ::/0	192.168.15.0/24, 10.0.1.0/24	Allowed IPs clients will use.
WG_PRE_UP	...	-	See config.js for the default value.
WG_POST_UP	...	iptables ...	See config.js for the default value.
WG_PRE_DOWN	...	-	See config.js for the default value.
WG_POST_DOWN	...	iptables ...	See config.js for the default value.

If you change WG_PORT, make sure to also change the exposed port.

Updating

To update to the latest version, simply run:

docker stop wg-easy
docker rm wg-easy
docker pull ghcr.io/wg-easy/wg-easy

And then run the docker run -d \ ... command above again.

Common Use Cases

• Using WireGuard-Easy with Pi-Hole
• Using WireGuard-Easy with nginx/SSL