-
Notifications
You must be signed in to change notification settings - Fork 320
Configuration
RaraAvis8 edited this page Feb 19, 2016
·
1 revision
All the information needed by chan_dongle is stored in /path_to_asterisk_config/dongle.conf.
[general]
interval=15 ; Number of seconds between trying to connect to devices
;------------------------------ JITTER BUFFER CONFIGURATION --------------------------
;jbenable = yes ; Enables the use of a jitterbuffer on the receiving side of a
; Dongle channel. Defaults to "no". An enabled jitterbuffer will
; be used only if the sending side can create and the receiving
; side can not accept jitter. The Dongle channel can't accept jitter,
; thus an enabled jitterbuffer on the receive Dongle side will always
; be used if the sending side can create jitter.
;jbforce = no ; Forces the use of a jitterbuffer on the receive side of a Dongle
; channel. Defaults to "no".
;jbmaxsize = 200 ; Max length of the jitterbuffer in milliseconds.
;jbresyncthreshold = 1000 ; Jump in the frame timestamps over which the jitterbuffer is
; resynchronized. Useful to improve the quality of the voice, with
; big jumps in/broken timestamps, usually sent from exotic devices
; and programs. Defaults to 1000.
;jbimpl = fixed ; Jitterbuffer implementation, used on the receiving side of a Dongle
; channel. Two implementations are currently available - "fixed"
; (with size always equals to jbmaxsize) and "adaptive" (with
; variable size, actually the new jb of IAX2). Defaults to fixed.
;jbtargetextra = 40 ; This option only affects the jb when 'jbimpl = adaptive' is set.
; The option represents the number of milliseconds by which the new jitter buffer
; will pad its size. the default is 40, so without modification, the new
; jitter buffer will set its size to the jitter value plus 40 milliseconds.
; increasing this value may help if your network normally has low jitter,
; but occasionally has spikes.
;jblog = no ; Enables jitterbuffer frame logging. Defaults to "no".
;-----------------------------------------------------------------------------------
[defaults]
; now you can set here any not required device settings as template
; sure you can overwrite in any [device] section this default values
context=default ; context for incoming calls, SMS and USSD
group=0 ; calling group
rxgain=0 ; increase the incoming volume; may be negative
txgain=0 ; increase the outgoint volume; may be negative
autodeletesms=yes ; auto delete incoming sms
resetdongle=yes ; reset dongle during initialization with ATZ command
u2diag=-1 ; set ^U2DIAG parameter on device (0 = disable everything except modem function)
; -1 not use ^U2DIAG command
usecallingpres=yes ; use the caller ID presentation or not
callingpres=allowed_passed_screen ; set caller ID presentation. By default use default network settings
; see http://www.the-asterisk-book.com/unstable/applikationen-setcallerpres.html
disablesms=no ; disable of SMS reading from device when received. Enable this option to disable
; sms reception. Use smsaspdu=yes to avoid problem when SMS is too long in TEXT mode.
smsaspdu=yes ; if 'yes' send SMS in PDU mode.
language=en ; set channel default language
mindtmfgap=45 ; minimal interval from end of previews DTMF from begining of next in ms
mindtmfduration=80 ; minimal DTMF tone duration in ms
mindtmfinterval=200 ; minimal interval between ends of DTMF of same digits in ms
callwaiting=auto ; if 'yes' allow incoming calls waiting; by default use network settings
; if 'no' waiting calls just ignored
disable=no ; if 'yes' no load this device and just ignore this section
exten=+1234567890 ; exten for start incoming calls, only in case of Subscriber Number not available!,
; also set to CALLERID(dnid)
dtmf=relax ; control of incoming DTMF detection, possible values:
; off - off DTMF tone detection, voice data passed to asterisk unaltered
; use this value for gateways or if you do not use IVR in diaplan
; inband - do DTMF tones detection
; relax - like inband but with relaxdtmf option
; default is 'relax' for backward compatibility
; dongle required settings
[dongle0]
audio=/dev/ttyUSB1 ; tty port for audio connection;
data=/dev/ttyUSB2 ; tty port for AT commands;
; or you can omit both audio and data parameters and use imei=123456789012345 and/or imsi=612849384756451
; imei and imsi must contain exactly 15 digits !
; imei/imsi discovery is available on Linux only
imei=123456789012345
imsi=612849384756451
; if you set audio and data parameter together with imei and/or imsi, audio and data is used.
; you can use both imei and imsi together. In this case exact match by imei and imsi is required.
; this is chunks of Asterisk extensions.conf file for show some chan_dongle features
[general]
[dongle-incoming]
; example of ussd receive
exten => ussd,1,Set(type=${USSD_TYPE})
; values from 0 till 5
; 0 - USSD Notify
; 1 - USSD Request
; 2 - USSD Terminated by network
; 3 - Other local client has responded
; 4 - Operation not supported
; 5 - Network time out
exten => ussd,n,Set(typestr=${USSD_TYPE_STR})
; type in string, see above
exten => ussd,n,Set(ussd=${USSD})
; USSD text, but may be truncated by first \n
exten => ussd,n,Set(ussd_multiline=${BASE64_DECODE(${USSD_BASE64})})
; USSD text, may be multiline
; Note: this exten run in Local channel not attached to anything, also all CALLERID() is empty
; example of sms receive
exten => sms,1,Set(sms=${SMS})
; SMS text, but may be truncated by first \n
exten => sms,1,Set(sms_multiline=${BASE64_DECODE(${SMS_BASE64})})
; SMS text, may be multiline
; Note: this exten run in Local channel not attached to anything, also CALLERID(num) is address of SMS originator
; example of begining context execution from not default exten
exten => +12345678901,1,Verbose(This exten executed if Subscriber Number is available and equal +12345678901 or exten setting value is +12345678901)
; example of channel variables setting by chan_dongle
exten => s,1,Set(NAME_OF_DEVICE=${DONGLENAME})
; for example 'dongle0' or 'dongle1' see dongle.conf
exten => s,n,Set(NAME_OF_PROVIDE=${DONGLEPROVIDER})
; for example see output of cli 'dongle show devices' column "Provider Name"
exten => s,n,Set(IMEI_OF_DEVICE=${DONGLEIMEI})
; for example see output of cli 'dongle show devices' column "IMEI"
exten => s,n,Set(IMSI_OF_SIMCARD=${DONGLEIMSI})
; for example see output of cli 'dongle show devices' column "IMSI"
exten => s,n,Set(CNUM_NUMBER=${DONGLENUMBER})
; Subscriber Number example see output of cli 'dongle show devices' column "Number"
; may be empty, use for save in SIM commands AT+CPBS="ON" and AT+CPBW=1,"+123456789",145
exten => s,n,Set(CNUM_NUMBER=${CALLERID(dnid)})
; Set to Subscriber Number if available
; applications of chan_DONGLE
exten => s,n,DongleStatus(dongle0,DONGLE0_STATUS)
; get status of device and store result in variable
; possible values of ${DONGLE0_STATUS}
; -1 invalid argument
; 1 device not found
; 2 device connected
; 3 device connected and in use
exten => s,n,DongleSendSMS(dongle0, "+18004005422", Hello how are you, Danila?, 1440, yes)
; send SMS on selected device and to specified number
; device name of Dongle device
; destination number in International format with leading '+' or w/o leading '+'
; message maximum 70 UCS-2 symbols
; validity period in minutes, will be round up to nearest possible value, optional default is 3 days
; report request if true report for this SMS is required, optional default is not
; functions of chan_dongle
exten => s,n,GotoIf($["${CHANNEL(callstate)}" == "waiting"]?waiting-call)
; now we provide channel function argument callstate
; possible values
; active ; enjoy and speek
; held ; this call is held
; dialing ; for outgoing calls
; alerting ; for outgoing calls, number dialed and called party ringing
; incoming ; for incoming calls
; waiting ; for incoming waiting calls;
; if callwaiting=no channels for waiting calls never created
; initialize ; never appear
; released ; never appear
; Answer on waiting call activate this call and place any other active calls
; on hold, but execution of dialplan for these calls not break stopped or frozen
; When active call terminated one of held becomes active.
exten => s,n,Set(CHANNEL(callstate)=active)
; if callstate is 'held' you can assign new value 'active'
; its mean activate this call and place on hold all other active calls but
; execution of dialplan for these calls not break stopped or frozen
exten => s,n,Dial(Dongle/g1/holdother:+79139131234)
exten => s,n,Dial(Dongle/r1/holdother:+79139131234)
exten => s,n,Dial(Dongle/p:PROVIDER NAME/holdother:+79139131234)
exten => s,n,Dial(Dongle/i:123456789012345/holdother:+79139131234)
exten => s,n,Dial(Dongle/s:25099/holdother:+79139131234)
; now we add option 'holdother' for dialing
; this option do
; 1) When looking for available devices by group, provider IMEI,
; IMSI prefix not ignore devices with whose state does not
; prohibit a new outgoing call when other call place on hold
;
; 2) Before actual dialing place active calls on hold
; but execution of dialplan for these calls not break stopped or frozen
; 3) This call will be active if succesfully answered
; BUG !!!
; tested for call waiting and hold features Huawei E1550 has a next bug:
; When local side hangup any call including held call ALL other calls LOST sound
; When remove side hangup active call ALL other calls LOST sound
; Please double check true this for you or not
; If true reduce usage of this useful features
exten => s,n,Dial(Dongle/g1/conference:+79139131234)
exten => s,n,Dial(Dongle/r1/conference:+79139131234)
exten => s,n,Dial(Dongle/p:PROVIDER NAME/conference:+79139131234)
exten => s,n,Dial(Dongle/i:123456789012345/conference:+79139131234)
exten => s,n,Dial(Dongle/s:25099/conference:+79139131234)
; and also option 'conference' added
; this option do
; 1) When looking for available devices by group, provider IMEI,
; IMSI prefix not ignore devices with whose state does not
; prohibit a new outgoing call when other call place on hold
;
; 2) Before actual dialing place active calls on hold
; but execution of dialplan for these calls not break stopped or frozen
; 3) If answered attach hold calls to conrefence (in term of GSM)
; Also if created outgoing channel place call on same device that incoming channel
; both incoming and outgoing channels become readonly to avoid the voice loop.
;
; see also BUG !!! note above