rebar3_grisp

Rebar plug-in for the GRiSP project. To obtain information about the plugin and its tasks, use the following command:

rebar3 help grisp [<task>]

📖 Table of content

rebar3_grisp

Installation

Globally

To install the plug-in globally, add the plug-in to your plug-ins list in ~/.config/rebar3/rebar.config:

{plugins, [
    rebar3_hex,
    rebar3_grisp
]}.

The first time you use Rebar the plug-in will be installed. To upgrade the plug-in to the latest version, you need to first update the Hex index and then the plug-in:

$ rebar3 update
===> Updating package registry...
===> Writing registry to ~/.cache/rebar3/hex/default/registry
===> Generating package index...
===> Writing index to ~/.cache/rebar3/hex/default/packages.idx
$ rebar3 plugins upgrade rebar3_grisp
===> Fetching rebar3_grisp ({pkg,<<"rebar3_grisp">>,<<"1.1.0">>})
===> Downloaded package, caching at ~/.cache/rebar3/hex/default/packages/rebar3_grisp-1.1.0.tar
===> Compiling rebar3_grisp

For an Existing Project

Add the plug-in to your rebar config:

{plugins, [rebar3_grisp]}.

Then just call your plug-in directly in the root of the existing application:

$ rebar3 grisp
===> Fetching grisp
===> Compiling grisp
<Plugin Output>

Create New Application

Prerequisites:

Install Plug-In Globally

To create a new GRiSP project:

rebar3 grisp configure

This command will provide you with a CLI that will guide you in the creation of your GRiSP project.

You can also use the command in a non-interactive way:

rebar3 grisp configure -i false

Unless stated otherwise, the non-interactive option will use the default values to create the GRiSP project. You can overwrite the default values in the command:

rebar3 grisp configure -i false --name="my_grisp_app" -n true -w true --ssid="mywifi" --psk="wifipsk"

This command will create a new GRiSP project named "my_grisp_app" with a network (-n true) and wifi (-w true) configuration already setup. The configuration will use the ssid "mywifi" and the psk "wifipsk".

Note that some options require others. For example, if you want to setup the ssid of the wifi, then you also need to activate the network and wifi configuration (-n true and -w true).

The specific variables provided by this plug-in are:

interactive activate the interactive mode
name is the name of the OTP application
dest is the destination path for deployment. This should point to where your SD-card is mounted (e.g. on macOS it is /Volumes/<NAME> where <NAME> is the name of the SD-card partition)
otp_version is the target Erlang/OTP version used on the GRiSP board
network specifies if the project contains network configuration files
wifi specifies if the project contains wifi configuration files. (requires network)
ssid is the ssid of the wifi network you want your board to connect to. (requires network and wifi)
psk is the psk of the wifi network you want your board to connect to. (requires network and wifi)
grisp_io specifies if you want your board to connect and use GRiSP.io. (requires network)
grisp_io_linking specifies if you want your board to link itself to GRiSP.io. (requires network and grisp_io)
token is your personnal GRiSP.io token. (requires network, grip_io and grisp_io_linking)
epmd specifies if you want your board to have epmd. (requires network)
cookie is the magic cookie that your board should use. (requires network and epmd)

Some variables are modfiable only through the command line. These variables are:

desc is the short description of the GRiSP application
copyright_year is the copyright year
author_name is the name of the author of the project
author_email is the email of the author of the project

For a full list of customizable variables as well as their short form, run rebar3 help grisp configure.

In the interactive mode you can also specify a few variables. During the CLI interaction, the questions related to these variable will be skipped. For example:

rebar3 grisp configure --name="mygrispapp"

Here the CLI won't ask you for the name of your GRiSP project because it's already provided.

Compile the project

rebar3 compile

Make sure you do that with the same Erlang version that you configured in the rebar.config. If you compiled rebar3 yourself with a more recent version of Erlang it will give errors, you will need to recompile rebar3 as well in that case.

For further information have a look at the GRiSP Wiki

Deploy an Application

To deploy a GRiSP application, use the command rebar3 grisp deploy. The command requires the release name and version to be provided. The deployment destination can be set in rebar.config or be given as an additional argument.

Example:

rebar3 grisp deploy --relname mygrispproject --relvsn 0.7.8

or shorter:

rebar3 grisp deploy -n mygrispproject -v 0.1.0

Above command will try to download a crosscompiled OTP version from our CDN and unpack it. In many usecases this will be enough. If you want to add own port drivers or NIFs in C you will have to build your own toolchain and OTP, see below.

Run rebar3 help grisp deploy for information on all arguments.

To generate a tarball with all the deployed files, add the option -t/--tar, all the files will be bundled in a a tarball under _grisp/deploy:

rebar3 grisp deploy --tar

Configuration

rebar.config:

{grisp, [
    {otp, [{version, "22.0"}]},
    {deploy, [
        % Path to put deployed release in
        {destination, "/path/to/destination"},

        % Shell script to run before deploying begins
        {pre_script, "rm -rf /path/to/destination/*"},

        % Shell script to run after deploying has finished
        {post_script, "umount /path/to/destination"}
    ]}
]}.

Generate GRiSP 2 Firmwares

The firmware command generates binary files that can be written on GRiSP 2 eMMC. There is three types of firmware that can be generated:

System Firmware: The system firmware is the content of a system partition on the eMMC. When using A/B software update, the system firmware can be written either on the first or the second system partition. By default, the command will generate a system firmware under _grisp/firmware but it can be disabled with the option -b false or --system false.
eMMC Image Firmware: The eMMC image firmware is a full image containing the bootloader, the partition table and the system partitions. It is meant to be written on the GRiSP 2 board to reset it completely with the new software. If the image is truncated (it is by default), the image only contains the first system partition. It means that when writing the firmware to the eMMC, the second system partition will be untouched. To generate an eMMC image firmware under _grisp/firmware, add the option -i or --image, to disable truncating so the image contains both system partitions, uses the option -t false or --truncate false.
Bootloader Firmware: The bootloader firmware contains only the bootloader and the partition table. To generate it under _grisp/firmware, add the option -b or --bootloader.

e.g.

Generate a system firmware for the default release:

rebar3 grisp firmware

Generate a system firmware for a specific release:

rebar3 grisp firmware --relname myapp --relvsn 1.2.3

Generate all firmwares, forcing existing files to be overwritten and forcing the generation of the software bundle even if one already exists in _grisp/deploy:

rebar3 grisp firmware --bootloader --image --force --refresh

Firmware Update

Description of the variables in the commands that will follow:

${RELNAME}: The relx release names used when generating the firmware.
${RELVSN}: The relx release version used when generating the firmware.
${USER}: The username of the account running the command.
${GRISP_BOARD_SERIAL}: The serial number of the GRiSP 2 board.

To write a system firmware to a GRiSP 2 board:

Copy the firmware to the SD card:

macOS $ cp _grisp/firmware/grisp2.${RELNAME}.${RELVSN}.sys.gz /Volumes/GRISP

Linux $ cp _grisp/firmware/grisp2.${RELNAME}.${RELVSN}.sys.gz /media/${USER}/GRISP
Unmount the SD card:

macOS $ diskutil umount /Volumes/GRISP

Linux $ umount /media/${USER}/GRISP
Open a serial console to the GRiSP board:

macOS $ screen /dev/tty.usbserial-0${GRISP_BOARD_SERIAL}1 115200

Linux $ screen /dev/ttyUSB1 115200
Insert the SD card in the GRiSP 2 board.
Reset the board using the onboard reset button.
Enter into barebox console mode by pressing any key before 3 seconds.
Consult the current active system partition:

Barebox $ echo $state.bootstate.active_system
Write the firmware. If the current active system is 0, use device /dev/mmc1.0, if it is 1 use device /dev/mmc1.1:

Barebox $ uncompress /mnt/mmc/grisp2.${RELNAME}.${RELVSN}.sys.gz /dev/mmc1.0
Remove the SD card.
Reset the GRiSP board again.

To reset a GRiSP 2 board eMMC, either with a truncated or full image firmware:

Copy the firmware to the SD card:

macOS $ cp _grisp/firmware/grisp2.${RELNAME}.${RELVSN}.emmc.gz /Volumes/GRISP

Linux $ cp _grisp/firmware/grisp2.${RELNAME}.${RELVSN}.emmc.gz /media/${USER}/GRISP
Unmount the SD card:

macOS $ diskutil umount /Volumes/GRISP

Linux $ umount /media/${USER}/GRISP
Open a serial console to the GRiSP board:

macOS $ screen /dev/tty.usbserial-0${GRISP_BOARD_SERIAL}1 115200

Linux $ screen /dev/ttyUSB1 115200
Insert the SD card in the GRiSP 2 board.
Reset the board using the onboard reset button.
Enter into barebox console mode by pressing any key before 3 seconds.
Set the current active system partition to the first one:

Barebox $ let state.bootstate.active_system=0

Barebox $ state -s
Write the firmware:

Barebox $ uncompress /mnt/mmc/grisp2.${RELNAME}.${RELVSN}.emmc.gz /dev/mmc1
Remove the SD card.
Reset the GRiSP board again.

To reset only the bootloader of the board:

Copy the firmware to the SD card:

macOS $ cp _grisp/firmware/grisp2.${RELNAME}.${RELVSN}.boot.gz /Volumes/GRISP

Linux $ cp _grisp/firmware/grisp2.${RELNAME}.${RELVSN}.boot.gz /media/${USER}/GRISP
Unmount the SD card:

macOS $ diskutil umount /Volumes/GRISP

Linux $ umount /media/${USER}/GRISP
Open a serial console to the GRiSP board:

macOS $ screen /dev/tty.usbserial-0${GRISP_BOARD_SERIAL}1 115200

Linux $ screen /dev/ttyUSB1 115200
Insert the SD card in the GRiSP 2 board.
Reset the board using the onboard reset button.
Enter into barebox console mode by pressing any key before 3 seconds.
Write the firmware:

Barebox $ uncompress /mnt/mmc/grisp2.${RELNAME}.${RELVSN}.boot.gz /dev/mmc1
Remove the SD card.
Reset the GRiSP board again.

Cautions

With truncated image firmwares

When writing a truncated eMMC image firmware, only the first system partition is written. If the active system is the second one, the board will continue to boot the old software. You will need to manually change the active system partition in the bootloader console and restart the board.

To consule the current active system partition in the bootloader console:

$ echo $state.bootstate.active_system

To change the current active system partition to the first one:

$ let state.bootstate.active_system=0
$ state -s

With writing system firmware on inactive system partition

When writing a system firmware, be sure to do it on the active system partition or the board will continue to boot the old software. The device for the first system is /dev/mmc1.0 and the one for the second system is /dev/mmc1.1. See the caution about truncated images firmware for details on how to consult and change the current active system partition.

Build Software Update Package

To create a GRiSP software update package, use the 'pack' command:

$ rebar3 grisp pack

It creates a software update package under _grisp/update.

To include the bootloader in the generate update package, add the option -b/--with-bootloader:

$ rebar3 grisp pack -b

Note that a toolchain is required for building the bootloader firmware, see the deploy command for more information on how to configure the toolchain.

To force the recreation of the bundle and firmware(s) use the option -r/--refresh:

$ rebar3 grisp pack -r

To generate a signed package, use the -k/--key option:

$ rebar3 grisp pack --key private_key.pem

Updating a GRiSP Board

To be able to update a GRiSP board using a software update package, the software running on the board must have the grisp_updater_grisp2 dependency in rebar.config:

{deps, [grisp_updater_grisp2]}.

grisp_updater needs to be configured in sys.config (or equivalent):

{grisp_updater, [
    {signature_check, true},
    {signature_certificates, {priv, my_app, "certificates/updates"}},
    {system, {grisp_updater_grisp2, #{}}},
    {sources, [
        {grisp_updater_tarball, #{}},
        {grisp_updater_http, #{
            backend => {grisp_updater_grisp2, #{}}
        }}
    ]}
]},

If signature_check is set to true the software package must be signed using the -k/--key option, and the public key must be available in the directory configured by signature_certificates.

When these conditions are met, you can follow these step to perform a A/B software update of a GRiSP board:

Unpack the software update package in some local directory:

any $ mkdir -p releases/${RELNAME}/${RELVSN} any $ tar -C releases/${RELNAME}/${RELVSN} -xvf _grisp/update/grisp2.${REL_NAME}".${RELVSN}.${PROFILE}.tar -xvf
Start a local HTTP server to serve the package:

any $ http-server ./releases -p 8000
Open a serial console to the GRiSP board:

macOS $ screen /dev/tty.usbserial-0${GRISP_BOARD_SERIAL}1 115200

Linux $ screen /dev/ttyUSB1 115200
On the GRiSP2 console, start the update process:

GRiSP $ grisp_updater:update(<<"http://${HOST_IP}:8000/${RELNAME}/${RELVSN}">>).
Reset the GRiSP2 board using the onboard reset button.
Validate the new software version on the GRiSP2 console:

GRiSP $ grisp_updater:validate().

Note that the update process will only show progress information if the log level is at least INFO.

Listing Packages

The plug-in can list pre-built GRiSP OTP packages and toolchains:

$ rebar3 grisp package list
===> GRiSP pre-built OTP versions for platform 'grisp2'
Version
23.3.4.11
23.3.4.9
$ rebar3 grisp package list --type=toolchain
===> GRiSP pre-built toolchain packages
OS     Latest  OS Version         Url
Linux  true    5.11.0-1027-azure  https://grisp.s3.amazonaws.com/platforms/grisp2/toolchain/grisp2-rtems-toolchain_Linux_5.11.0-1027-azure_e2c29d3374d9046af01af570f6a85a6aa99546bb.tar.gz
Linux          5.11.0-1028-azure  https://grisp.s3.amazonaws.com/platforms/grisp2/toolchain/grisp2-rtems-toolchain_Linux_5.11.0-1028-azure_3122986b9cd7073f42f1387f3981c812a2909b68.tar.gz
macOS  true    10.15.7            https://grisp.s3.amazonaws.com/platforms/grisp2/toolchain/grisp2-rtems-toolchain_macOS_10.15.7_e2c29d3374d9046af01af570f6a85a6aa99546bb.tar.gz
macOS          11.6.3             https://grisp.s3.amazonaws.com/platforms/grisp2/toolchain/grisp2-rtems-toolchain_macOS_11.6.3_3122986b9cd7073f42f1387f3981c812a2909b68.tar.gz

Build OTP for GRiSP

The fastest way is to use our docker image grisp/grisp2-rtems-toolchain:

Add the toolchain image name to the rebar.config under grisp → build → toolchain → docker

Or if you have a local installation you can use that:

Add the path to the toolchain to the rebar.config under grisp → build → toolchain → directory

{grisp, [
    {otp, [{version, "25"}]},
    {build, [
        {toolchain, [
            {directory, "/PATH/TO/TOOLCHAIN-ROOT"}
            % Or use docker
            {docker, "grisp/grisp2-rtems-toolchain"}
            % If both are specified, only 'directory' is used
        ]}
    ]},
    {deploy, [
        {destination, "/PATH/TO/DESTINATION"}
    ]}
]}.

Then execute rebar3 grisp build. This will take some time, because Erlang/OTP is cross-compiled for the GRiSP board.

You only need to do that again if you updated and rebuilt the grisp2-rtems-toolchain repository or if you changed or wrote new drivers in C. If you need to build OTP for a second time and just changed files you can speed it up by using rebar3 grisp build --configure false. Each time you add new C files you will need to run configure again, because this tool will apply a patch to a makefile for each C driver, NIF and system file.

You can create the tarballs we use for distribution on our CDN with rebar3 grisp build --tar true

The built Erlang distribution and its runtime system is located in the project folder, under the path _grisp/otp/<version>/install.

Bug reports

You can run rebar3 grisp report to gather info about the project configuration. The user can view and edit the generated text files. It's possible to pack them later adding --tar to the same command. Providing such report file can speedup debugging and support from the dev team.

Development

To test the plug-in and develop for it, we recommend checking out a specific version into a local project. You can also create a new temporary GRiSP project using this plug-in. This can be useful to test deployments locally before copying them to an SD card:

$ rebar3 new grispapp name=grisp_test dest=/tmp/GRISP_SD_CARD

Go into the project folder and prepare the checkout directory used by Rebar 3 for dependency overrides:

$ cd grisp_test
$ mkdir -p _checkouts

Testing `master`

You need to clone both rebar3_grisp (this repo) and its dependency grisp_tools. If you want the latest master versions:

$ git clone git clone https://github.com/grisp/rebar3_grisp.git _checkouts/rebar3_grisp
$ git clone git clone https://github.com/grisp/grisp_tools.git _checkouts/rebar3_grisp

Testing a Specific Branch

Alternatively, clone a specific branch. Replace $REBAR3_PLUGIN_BRANCH with the branch name you want from rebar3_grisp and $GRISP_TOOLS_BRANCH with the branch name you want from grisp_tool:

$ git clone git clone --single-branch --branch $REBAR3_PLUGIN_BRANCH https://github.com/grisp/rebar3_grisp.git _checkouts/rebar3_grisp
$ git clone git clone --single-branch --branch $GRISP_TOOLS_BRANCH https://github.com/grisp/grisp_tools.git _checkouts/rebar3_grisp

In case you only need a specific branch of rebar3_grisp, you can default to using the master version of grisp_tools.

Name		Name	Last commit message	Last commit date
Latest commit History 224 Commits
.github/workflows		.github/workflows
.scripts		.scripts
priv/templates		priv/templates
src		src
.github_changelog_generator		.github_changelog_generator
.gitignore		.gitignore
CHANGELOG.md		CHANGELOG.md
LICENSE		LICENSE
README.md		README.md
erlang_ls.config		erlang_ls.config
rebar.config		rebar.config
rebar.lock		rebar.lock

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Repository files navigation

rebar3_grisp

Installation

Globally

For an Existing Project

Create New Application

Compile the project

Deploy an Application

Configuration

Generate GRiSP 2 Firmwares

Firmware Update

Cautions

With truncated image firmwares

With writing system firmware on inactive system partition

Build Software Update Package

Updating a GRiSP Board

Listing Packages

Build OTP for GRiSP

Bug reports

Development

Testing `master`

Testing a Specific Branch

About

Releases 30

Packages

Contributors 11

Languages

License

grisp/rebar3_grisp

Folders and files

Latest commit

History

Repository files navigation

rebar3_grisp

Installation

Globally

For an Existing Project

Create New Application

Compile the project

Deploy an Application

Configuration

Generate GRiSP 2 Firmwares

Firmware Update

Cautions

With truncated image firmwares

With writing system firmware on inactive system partition

Build Software Update Package

Updating a GRiSP Board

Listing Packages

Build OTP for GRiSP

Bug reports

Development

Testing master

Testing a Specific Branch

About

Topics

Resources

License

Stars

Watchers

Forks

Releases 30

Packages 0

Contributors 11

Languages

Testing `master`

Packages