Parts to 3D Print

Print all parts with the following print settings:

• PLA (Two PETG exceptions exist! See below)
• 0.4mm nozzle
• No supports
• 0.2mm layer height
• 6 perimeter layers (This is especially critical for parts that have heat-set inserts)
• 20% infill
• printable in the provided orientations
• outer perimeter layer first
• 2-3mm brim recommended, but not required

However, exceptions do exist! Please check the breakdown below for exceptions.

Note that parts that peel off the bed with a small curl cannot be used. They must stick to the bed such that they remain flat.

Other materials, such as PETG, may also work. We welcome feedback on various materials if others find them successful.

Frame Printed Parts and Quantities

• 1x PSU Socket Holder
• 1x Left Crossbar Pulley Reinforcement Plate
• 1x Right Crossbar Pulley Reinforcement Plate
• 1x Left Corner Pulley Reinforcement Plate
• 1x Right Corner Pulley Reinforcement Plate
• 2x Motor Reinforcement Plate
• 1x x_limit_trigger.STL
• 3x z_thrust_bearing_spacer.STL
• 1x back_z_motor_plate.STL
• 1x front_left_z_motor_plate.STL
• 1x front_right_z_motor_plate.STL
• 2x belt_clasp.STL
• 1x front_left_leadscrew_retainer.STL
• 1x front_right_leadscrew_retainer.STL
• 1x back_leadscrew_retainer.STL
• 1x back_right_foot.STL
  • 2 perimeter layers is sufficient
• 1x back_left_foot.STL
  • 2 perimeter layers is sufficient
• 1x front_right_foot.STL
  • 2 perimeter layers is sufficient
• 1x front_left_foot.STL
  • 2 perimeter layers is sufficient
• 1x front_left_bed_coupling_lift.STL
• 1x front_right_bed_coupling_lift.STL
• 1x back_bed_coupling_lift.STL
• 1x left_motor_plate.STL
  • print from PETG
  • Note: an aluminum version of this part is now available.
• 1x right_motor_plate.STL
  • print from PETG
  • Note: an aluminum version of this part is now available.
• 1x left_motor_corner_plate_spacer.STL
• 1x right_motor_corner_plate_spacer.STL
• 1x left_double_pulley_corner_bracket.STL
  • print with support material
• 1x right_double_pulley_corner_bracket.STL
  • print with support material
• 4x printed_pulley_spacer.STL

Toolchanger Parts and Quantities

• 1x Twist Lock Spacer
• 1x carriage_back_plate.STL
• 1x carriage_center_plate.STL
• 1x carriage_coupler_plate.STL
• 1x carriage_pulley.STL
• 1x fixed_half_pulley.STL
• 1x floating_half_pulley.STL
  • print with support material
• 1x lock_actuator_base_plate.STL
• 1x lock_actuator_motor_clip.STL
• 1x OPTTIONAL spring_guide_anchor_block.STL

Extruder-Specific Frame Parts

• 1x ooze_wiper.STL per tool
• 1x tool_cable_management_bracket.STL per tool
• 1x parking_post_base_47mm.STL per tool
• 1x tool_holder_47mm.STL per tool

Assembly Fixtures Parts and Quantities

• 1x coupling_plate_pin_insertion_fixture.STL
• 1x z_lift_pin_insertion_fixture.STL
• 8x outer_frame_squaring_plate.STL