Ohai refinements

Added changes to Ohai instructions for drag chain and packout

docs/lumen/drag-chain/index.md

@@ -18,7 +18,9 @@ This section will guide the reader on how to properly assemble the LumenPNP v3.1
 
 ##Assembling the Drag Chain
 
-1. Mount the drag chain onto the cable routing jig, and fix in place with a screw on the motherboard side. Ensure the side with the end link in the original orientation is faced towards the motherboard end of the cable routing jig, and the side with the end link reversed from the previous step is faced towards the X Gantry side of the jig. 
+1. Mount the drag chain onto the cable routing jig. Ensure the side with the end link in the original orientation is faced towards the motherboard end of the cable routing jig, and the side with the end link reversed from the previous step is faced towards the X Gantry side of the jig. 
+
+1. Fix in place with a screw on the motherboard side end link
 
     ![](img/MountDragChain.jpeg)
 
@@ -88,10 +90,12 @@ This section will guide the reader on how to properly assemble the LumenPNP v3.1
 
     ![](img/XMCableRight.jpeg)
 
-1. Route XM Cable through the zip ties and the retaining slot of `x-cable-chain-bracket`. Install the bracket between the 12th and 13th drag chain covers. Cable retaining slot of the bracket should face towards the motherboard side of the drag chain, with the XM cable exiting towards the user once in final position. 
+1. Route XM Cable through the zip ties and the retaining slot of `x-cable-chain-bracket`. Cable retaining slot of the bracket should face towards the motherboard side of the drag chain, with the XM cable exiting towards the user once in final position. 
 
     ![](img/XMCableandBracketInstall1.jpeg)
 
+1. Install the bracket between the 12th and 13th drag chain covers. Slide the drag chain covers into the slots in the side of `x-cable-chain-bracket`
+
 1. Close the drag chain covers holding the `x-cable-chain-bracket` in place. Pull XM cable through until slack is removed. 
 
     ![](img/XMCableandBracketInstall2.jpeg)

docs/lumen/pack-out/index.md

@@ -25,15 +25,23 @@
 1. Insert `y-gantry-left` into the tray
 
     ![](img/remove-left-legs.png)
+
+1. Insert 2x `back-leg-extension` into the tray
+
+    ![](img/backlegextension.jpg)
+
+1. Insert 2x `front-leg-extension` into the tray
+
+    ![](img/frontlegextension.jpg)
 
 1.  Confirm the lower foam tray matches the image shown below before continuing:
 
-    ![](img/IMG_5122.jpeg)
+    ![](img/IMG_5122.jpg)
 
  1. Place the packaged lower foam tray into the LumenPnP packaging
 	* Orient the tray so that the packaged `x-gantry` is closer to the Opulo logo side of the box 
 
-    ![](img/lower-tray-v3.1.png)
+    ![](img/lower-tray-v3.1.jpg)
 
 
 ## Package upper foam tray
@@ -52,13 +60,16 @@
     * `Bagged-10x-extrusion-cable-clips`
 
 1. Insert the following into the right-side cavity of the foam tray:
-    * `2x front-leg-extension`
-    * `2x back-leg-extension` 
+
     * `front-drag-chain-mount`
     * `aux-staging-plate-foot`
     * `static-camera-foot`
     * `Bagged-10x-extrusion-cable-clips`
 
+    	<img src="img/toplayerrightarrangement.jpg" width="60%"/>
+
+    ![](img/toplayerrightarrangement.jpg)
+
 1. Insert the following into the left-side cavity of the foam tray:
     * `24v6A-power-supply`
     * `power-cable` 
@@ -67,27 +78,27 @@
 
 1. Insert a foam block above each side of `primary-staging-plate`
 
- 	![](img/IMG_5127.jpeg)
+ 	![](img/IMG_5127.jpg)
 
 1. Insert `aux-staging-plate` on top of `primary-staging-plate`
 
 1. Insert `front-feeder-rail` and `rear-feeder-rail` into the foam tray
 
- 	![](img/removing-front-and-back-rails.png)
+ 	![](img/removing-front-and-back-rails.jpg)
 
 1. Insert `drag-chain-assembly` above the feeder rails
 
-  	![](img/removing-cable-chain.png) 
+  	![](img/removing-cable-chain.jpg) 
 
 1. Confirm the upper foam tray matches the image shown below before continuing:
 
- 	![](img/IMG_5126.jpeg)
+ 	![](img/IMG_5126.jpg)
 
 1. Place the packaged upper foam tray into the LumenPnP packaging
     * Orient the tray so that the staging plates are closer to the Opulo logo side of the box
 
     ![](img/first-tray-removal.png)
-    ![](img/first-tray-v3-1.png)
+    ![](img/first-tray-v3-1.jpg)
 
 ## Serialize the outer box